Chicco LITEWAY 2 Bedienungsanleitung Seite 13

ton located on the backrest. Release the button to lock the
backrest in the nearest position (Fig. 6).
7. To raise the backrest to the desired position, simply push
it upwards (Fig. 7).
WARNING: The child's weight can make these operations
more difficult.
HOW TO ADJUST THE LEGREST
The stroller's legrest can be adjusted in 2 positions for your
child's improved comfort.
8. To adjust the position of the legrest, turn the two lateral le-
vers up until you reach the horizontal locking position (fig. 8).
9. To return to the starting position, press the lateral buttons
(fig. 9).
WARNING: The legrest does not have the function to re-
tain the child.
REAR BRAKES
The rear wheels have linked brakes, which can be applied
simultaneously to the two rear wheels by using just one
pedal.
10. To apply the brakes, push one of the two levers located
at the centre of the rear wheel units in a downward direc-
tion, as shown in fig. 10.
11. To unlock the braking system, push one of the two le-
vers located at the centre of the rear wheel units in an up-
ward direction, as shown in fig. 11.
WARNING: Always apply the brakes whenever the stroller
is stopped. Never leave the stroller on a sloped surface, with
a child inside, even with the parking brakes engaged.
WARNING: After operating the brake lever, ensure that
the brakes are correctly engaged in both of the rear wheel
units.
FRONT SWIVEL WHEELS
The stroller has front swivel/fixed wheels. It is recommend-
ed to use the wheels in the fixed mode on particularly
changeable surfaces. The use of the wheels in the swivel
mode is recommended in order to increase the control of
the stroller on a normal road surface
12. To use the front wheels in the swivel mode, push the
front lever in an upward direction with your foot, as shown
in fig. 12. To use the front wheels in the fixed mode, lower
the lever with the foot. The wheel will lock in the straight
position, regardless of its previous position.
WARNING: Both wheels must always be locked or un-
locked at the same time.
SUMMER/WINTER HOOD
13. To fit the hood, fasten the plastic clip in the appropriate
positions, as shown in fig. 13A. To complete fitting the hood
on the seat, fasten the rear part of the hood on the back
of the stroller backrest using the relevant buttons (fig 13B).
WARNING: The hood must be fixed on both sides of the
stroller. Ensure that the hood is correctly secured into po-
sition.
14. Open the hood as shown in fig. 14A. Close the hood
pulling the front part towardS you as shown in fig. 14B.
15. The hood can become a summer sun-canopy. The rear
panel may be removed by unfastening the zip and buttons
on the rear side of the backrest (fig. 15).
16. The hood features an extractable flap that helps pro-
tecting your child from intense light (fig. 16)
HOW TO CLOSE THE CHAIR
WARNING: When opening the stroller, make sure that your
child or other children are at a safety distance. Make sure
that during these operations the moving parts of the stroll-
er will not come into contact with your child Before closing
the stroller, ensure that the storage basket is empty.
17. To close the stroller, pull the rear locking mechanism in
an upward direction (fig. 17A), and unlock the pedal, locat-
ed on the right side of the stroller, with your foot (see fig.
17B).
18. To close the stroller completely, push the handles for-
ward (fig. 18).
19. When the stroller is closed, the locking device located
on the side of the stroller will automatically lock it in the
close position (see fig. 19), therefore preventing any acci-
dental opening of the stroller.
HOW TO REMOVE THE FABRIC COVER
The fabric cover of the stroller can be removed. 20. To re-
move the fabric cover, raise the legrest (fig. 20A). Then
unfasten the buckle (fig. 20B), the press studs on the seat
(fig. 20C) and the velcro straps around the lower part of the
backrest bar (fig. 20D); remove the fabric cover, taking care
to slide the safety harness through the appropriate hole. 21.
Unfasten the press studs located on the rear tubes of the
stroller, as shown in fig. 21A. Unfasten the press stud C and
remove the two hooks D and E, located under the fabric
panel on the side of the stroller (fig. 21B). Lastly, remove
the fabric cover from the backrest, pulling it in an upward
direction. Follow the steps above in reverse order to fit the
lining again.
WARNING: Check regularly that the belt under the seat is
tensioned (fig. 20B).
ACCESSORIES
WARNING: The accessories described below may not be
available for some versions of this product. Please read
carefully the instructions on the accessories available for
the model purchased.
STORAGE BASKET
The stroller may come with a storage basket.
22. Fasten the basket by passing the front slots through
the supports A. Fasten the velcro straps around the tubes
B; Then pass the rear straps around the tubes C and fasten
the press studs (fig. 22).
WARNING: Do not overload the storage basket. Maximum
weight 3 Kg.
RAIN COVER
The stroller may come with a rain cover.
23. To fit the rain cover, pass the straps around the tubes of
the stroller in the positions shown in fig. 23 and fasten the
velcro on the back of the rain cover.
After use, if the rain cover is wet, let it dry in the air before
folding the rain cover to store it.
WARNING: Be extremely careful when using the rain cover.
WARNING: Do not use the rain cover if the stroller is not fit-
ted with the hood or sun canopy to prevent the risk of suf-
focation. When the rain cover is fitted on the stroller, never
leave it exposed to direct sunlight with the child inside, as
the temperature will rise considerably.
13