Fontanot Magia70 Montageanleitung Seite 6

24. Secure element F01 to the floor in a position corresponding to the first baluster C03, drilling a hole with a
Ø 8 mm bit. Use elements C58, B12, B83 and B02 (fig. 1).
25. Identify the segments of the handrail not marked in red A22 and the one marked in red A23, which will be used
on landing E06 (fig. 9).
26. Start modelling the handrails A22 not market in red and try to give them a curve which follows the staircase as
much as possible (fig. 1).
27. Start from baluster C03 connecting landing E06 and tread L34, and begin by securing handrail A22, which has
just been bent. Use elements C64 with the screwer.
Warning: position the seam of the coating on the handrail facing the bottom.
28. Join the other segments of handrail A22, tightening, gluing and shaping them one after the other. Use elements
B33, and D35. Position the thickest part of D35 towards the outside.
29. Saw off any excess handrail next to the first C03 baluster of the staircase using a hacksaw.
30. Complete handrail A22 by securing element A21 using elements C64 and the glue (X01) (fig. 1).
31. Insert all of the other balusters into elements F48, which were secured to treads L34 previously. Tighten
element B02 and fasten to handrail A22, taking care to ensure that they are vertical. We recommend assembling
the shorter balusters first.
32. Check the linearity of the handrail A22 and correct using a rubber hammer, if necessary.
33. Complete railing assembly by inserting elements B82 into the lower part of the balusters C03 (fig. 1-1C).
Assembling the balustrade
34. Assemble column C04 onto element G01, which protrudes from landing E06 (fig. 8).
35. Position elements F01 on landing E06 using elements C58 and B02. Drill landing E06 using a Ø 5 mm bit,
maintaining the same centre to centre distance between the holes as the one used between the balusters C03
of the railings assembled before.
36. Position the shorter balusters C03 (H 935 mm) and tighten elements B02 of parts F01 (fig. 1).
37. Secure element A24 onto column C04 using element B02. Then, fasten the handrail A23 marked with the letter
"R" using screw C64 (fig. 1).
38. Fasten handrail A23 to the column C03 nearest to the landing, using screws C64 and making sure that they are
perfectly vertical. Repeat the same procedure for all of the balusters C03 present on landing E06.
39. Saw off any handrail in excess using a hacksaw. Complete handrail A22 by securing element A21 using elements
C64 and the glue (X01) (fig. 1).
40. Based on the position and the existence of walls around the opening of the staircase, one or two extra balusters
C03 (H 935 mm) may need to be positioned (fig. 10).
41. In this case, consider a space equidistant from the other balusters or from the wall.
To secure these, we recommend drilling landing E06 with a Ø 5 mm bit and using elements F01, C58, and B02.
We also recommend drilling the floor with a Ø 12 mm bit and using elements F01, B23, B27, C84, C85 and B02
(fig. 11). If necessary, secure the balustrade on the landing to the balustrade on the floor, (fig. 10), model the
handrails carefully, following well-secured curves. Any wrinkles that form on the inside of the handrails are not a
defect, rub energetically (generating heat) with a paper tower until they disappear.
Final Assembly
42. To further stiffen the staircase at intermediate points, secure elements F09 to the wall and join using elements
F08, with balusters C03. Drill using a Ø 8 mm point and use elements C50, C49, C58, B12 (fig. 12).
7 - Magia 70