Fontanot Magia70 Montageanleitung Seite 5

English
Unpack each element of the staircase before starting to assemble them. Arrange them on an ample surface and
check quality (TAB. 1: A = Code, B = Quality).
Preliminary assembly
1. Insert the dowels B02 into the elements F48 without tightening completely. Mark the position of the holes using
the template present in the package. Drill a hole using a Ø 4.5 mm bit and fasten elements F48 using screws
BB5 (fig. 2).
2. Carefully measure the height from floor to floor to determine the number of spacer rings D45 and prepare above
its spacer D47 (TAB. 2).
3. Assemble elements C63, C65, and C66 onto the balusters C03 (fig. 3).
4. Assemble the base G03, B17 and B46 (fig. 1).
Assembly
5. Determine the centre of the opening on the floor and position the base (G03+B17+B46) (fig. 4).
6. Drill using a Ø 14 mm point and secure the base (G03+B17+B46) to the floor with elements B13 (fig. 1).
7. Tighten the tube G02 onto the base (G03+B17+B46) (fig. 1).
8. Insert the base cover D46 into the tube G02 (fig. 5).
9. Insert the following in order: spacer rings D45, metal spacer D47, spacer rings D45 the first tread L34, spacer
ringsD45, metal spacer D47, spacer ringsD45 and then a tread L34 again, and so forth. Position the treads,
alternating between right and left, so that the weight is evenly distributed (fig. 5).
10. Once you have reached the end of the tube G02, tighten element B47, tighten the following tube G02 and
continue assembling the staircase (fig. 5).
11. Once you have reached the end of the tube G02, screw element B46 and element G01 (screw element G01
taking into account the fact that it must be 15 cm taller than the height of the staircase, as shown in fig. 6).
Continue to insert the treads using element D01 inserted in the final treads L34, which are not centred on pole
G02.
12. Lastly, insert the landing E06. After choosing the direction of rotation (fig. 7), position the landing (see point 13)
on the tread arrival side L34 (fig. 8). (fig. 4). Establish the position of the holes using the template provided, drill
the landing using a Ø 4.5 mm bit and assemble element F48 using parts B02 and C57.
13. Insert element B05, B04 and secure element B03 sufficiently, keeping in mind that the treads must still rotate
(fig. 1).
Fixing the landing
14. Move element F12 next to the floor. Establish the position, maintaining a distance of approximately 15 cm
from the outer edge of landing E06, drill a hole using a Ø 14 mm bit and secure in a permanent manner using
elements B13 (Fig. 1).
15. Secure elements F12 to landing E06 using elements C58 (drill landing E06 with a Ø 5 mm bit).
16. Position elements B95.
To assemble the railing
17. Fan the treads out L34. You can now climb the stairs.
18. Start from landing E06, insert the longer balusters C03 (H 1190 mm) connecting treads L34.
Position the balusters C03 with element C63 with the opening towards the top (fig. 8). Only tighten element B02
from the lower tread (fig. 2).
19. Check that all the balusters C03 positioned are vertical. Take care during this operation because very important
to assembling the staircase correctly.
20. Tighten element B03 in a permanent manner (fig. 8).
21. Only tighten element B02 from the upper tread (fig. 2).
22. Check that the balusters C03 are vertical again and correct, repeating the operations described above if
necessary.
23. To calculate the exact height of the starting baluster C03, proceed as follows: Position a baluster C03
(H 1190 m) inside element F48 and insert it into element F01, which must then be secured to the ground.
Measure the distance between the upper part of the starting tread L34 and the end of baluster C03, which has
just been inserted. Compare the figure obtained with the one for the balusters C03 mounted previously, and cut
to obtain the same height for all the balusters C03 in the staircase (fig. 1).
6 - Magia 70