Start-Up Of The Device/Introduction; Infrared Remote Control; General Operation - AEG mc 4409 cd mp3 Bedienungsanleitung

Start-up of the device/Introduction

• Read the operating instructions thoroughly before the start-up!
• Select an appropriate location for the device, e.g. a dry, fl at,
non-slip surface on which the device can be easily operated.
• Make sure that the device is adequately ventilated!
• Connect the loudspeakers to the back of the music centre to
the sockets market „Speaker RIGHT and LEFT" (28).
• Insert the plug into a properly installed 230 V, 50 Hz power
socket. Please ensure that the mains voltage corresponds to
the information on the type plate.
Setting the Time (in Standby Mode)
1. Keep the MEM/CLK-ADJ button (10/6) pressed down. The
words „24 HOUR" appear in the display.
2. Use the << SKIP/TUNING >> buttons (8/3) to choose
between the 24 hour and 12 hour display. Press the MEM/
CLK-ADJ button (10/6) to confi rm.
Note: The following appears in the case of the 12 hour
display
AM = in the morning, PM = in the afternoon/evening.
3. Press the << SKIP/TUNING >> buttons (8/3) to set the
hours. Keep the button pressed down until the desired
hour is reached. Press the MEM/CLK-ADJ button (10/6) to
confi rm.
4. Press the << SKIP/TUNING >> (8/3) button in order to set
the minutes. Keep the button pressed down until the desired
minutes are reached.
5. Press the MEM/CLK-ADJ button (10/6) again to store the
time.
Remote Control Batteries (not supplied)
• Open the lid of the battery compartment on the back of the
remote control.
• Insert 2 batteries of type R6 „AA" 1,5 V. Ensure that the
polarity is correct (see the fl oor of the battery compartment)!
• If the remote control is not used for a prolonged period,
remove the batteries in order to prevent battery acid leaking.
• Different battery types or new and used batteries must not
be used together.
Warning: batteries are not to be disposed of together with
domestic wastes. Dispose of the used batteries at the relevant
collection bin or at your dealer's.
Never throw batteries into the fi re.
CD deck transport protection
Please open the CD compartment (11) by pressing the
(open) button (12). Remove the transport protection from the CD
player if present before use.

General Operation

STANDBY/ON (4/12)
Switch the device to the standby mode with the STANDBY/ON
button (the time is displayed). If this button is pressed once
more, the device switches on again.
05-MC 4409 CD AEG 49
Volume (5/10)
This is used to set the individual volume. The letters „VOL" and a
fi gure appear in the display (13). This corresponds to the volume
that has been set as far as „VOL 30" or „VOL 00".
PHONES Headphone Socket (1)
Please use headphones with a 3.5 mm stereo jack plug; these
should be inserted into the headphone socket. The loudspea-
kers are then switched off.

Infrared remote control

For operating the music centre from a distance of up to 5 metres
without a lead. If the range of the remote control is reduced, the
batteries have to be replaced. During operation ensure that there
is nothing blocking the direct line between the remote control
and the sensor (3) on the machine.
USB Connexion (7)
This device has been developed in accordance with the latest
technical developments in the USB fi eld. Unfortunately the large
number of different types of USB storage media on offer today
makes it impossible to guarantee full compatibility with all USB
storage media. For this reason there may be problems in rare
cases with playing back from USB storage media. This is not a
malfunction of the device.
1. In order to switch on the device please press the STANDBY/
ON switch (4/12).
2. Now press the FUNCTION button (6/8) to select the CARD-
USB mode.
3. Connect a USB storage medium (the control lamp (26) lights
up in red).
4. Press PLAY/PAUSE (14/1) to play back the music data.
For operating instructions please see the section "Playing
CDs/MP3s".
Note:
• The FIND function is restricted.
• With the SD/MMC card inserted it is not possible to switch
over to the USB connection.
Important: Before removing the USB storage medium, switch
the device to TUNER operation using the TUNER/BAND button
(27/13).
SD/MMC Card Slot (9)
1. If you would like to play back data on an SD/MMC card
please insert it into the opening provided.
2. Now press the FUNCTION button (6/8) to select the CARD-
USB mode (the control lamp (26) lights up in green).
3. Press PLAY/PAUSE (14/1) to play back the music data.
For operating instructions please see the section "Playing
CDs/MP3s".
Note: The FIND function is restricted.
49
28.07.2006, 11:03:31 Uhr