Intended Use; Start-Up Of The Device/Introduction - AEG MC 4443 CD/MP3 Bedienungsanleitung

English
36
10 TUNING control
11 USB connection
12 BAND Band selection switch (AM / FM / FM ST.)
13 SKIP+ button (reverse search)
14 SKIP- button (forward search)
15 MODE button (repeat/random)
16 IR Sensor for the remote control
17 FM ST. control lamp
18 POWER control lamp
Reverse Side
19 SPEAKERS R/L Loudspeaker connections
20 Battery compartment (Power reserve)
21 AC Mains connection
22 FM ANT. throw-out aerial
Remote Control
1 button (Play/Pause)
2 PROG button (memory)
3 / buttons (reverse search/forward search)
4 ALBUM button (up album)
5 +10 button
6 MODE button (repeat/random)
7 STOP button

Intended Use

This device is used for:
• The reception of radio programmes
• Playing back audio/MP3 CDs
• Sound playback from external audio sources.
It is intended exclusively for this purpose and may only be
used as such.
It may only be used in the manner described in these instruc-
tions for use. The device must not be used for commercial
purposes.
Any other use of this device is considered to be contrary to
the intended use and may result in damage to materials or
even personal injury.
The firm ETV – Elektro-Technische Vertriebsgesellschaft mbH
does not accept any liability for damage caused as a result of
the use of this device contrary to its intended use.

Start-up of the device/Introduction

• Read the operating instructions thoroughly before the
start-up!
• Select an appropriate location for the device, e.g. a dry,
flat, non-slip surface on which the device can be easily
operated.
• Make sure that the device is adequately ventilated!
• Connect the loudspeakers to the back of the music
centre to the sockets market "Speaker R and L" (19).
• Remove the protective film from the display if it is still
present.
Power Supply
• Insert the plug into a properly installed 230 V, 50 Hz
power socket.
• Please ensure that the mains voltage corresponds to the
information on the type plate.
Setting the Time (in standby mode (OFF))
• Perform the settings with the buttons SKIP+/ SKIP-
(13/14/3).
• Confirm your entries with the
ton (6/1).
1. Keep the PLAY/PAUSE/USB button (6/1) pressed
down. The notification "24 H" appears in the display.
2. You may now successively perform the settings for the
display format (24 H or 12 H), the hours and the minutes.
NOTE:
In the 12-hour notification, the following will appear in the
display:
AM = in the morning; PM = in the afternoon/evening
NOTE:
Storage/display of the time is lost as soon as the electric-
ity supply is interrupted. If you would like to have the time
displayed even when the power is disconnected, insert a
button cell of type CR 2025 with the correct polarity in the
battery compartment (20) (battery not supplied). Open the
lid of the battery compartment on the back by turning in
the direction of OPEN.
Inserting the Batteries
NOTE:
The lithium cell in the battery compartment of the remote
control has been secured for transport with a foil. This
prolongs the lifetime of the battery. Before initial use please
remove this foil so that the remote control is ready for
operation.
The battery of the remote control is a long-life lithium cell. If
the range of the remote control is reduced during use, please
proceed as follows:
• Open the battery compartment on the back of the
remote control.
• Replace the cell by a battery of the same type (CR 2025).
Ensure correct polarity.
• Then close the battery lid.
If the remote control is not used for a prolonged period,
remove the batteries in order to prevent battery acid leaking.
CAUTION:
Batteries are not to be disposed of together with domestic
wastes. Dispose of the used batteries at the relevant collec-
tion bin or at your dealer' s .
PLAY/PAUSE/USB but-