Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SAFETY INSTRUCTIONS
Read the entire instruction manual before you start installation and
assembly and keep it for future reference.
1.
Protect this device from water, humidity and other liquids. Avoid
using/storing it in extreme temperatures. Do not expose it to direct
sunlight and other sources of heat.
2.
Protect this device from shock and being dropped.
3.
Do not use the product for purposes different from displayed in this
operating manual.
4.
Appliance for household use only.
5.
Do not apply too much pressure on the device. Applying too much
pressure on the device will cause the rotating blade to stop. Reducing
pressure releases the blade.
6.
Do not use the device on clothes you are wearing.
7.
Do not use the device on damp clothes.
8.
Exercise special caution when using the device near buttons, stitching,
zips, patches etc.
9.
Keep the device out of the reach of children.
10. Use only specified batteries.
11. Use only authorized accessories.
12. Do not place the appliance in water or any liquid; nor handle/use it
with wet or moist hands.
13. Do not use this device if it has been damaged and malfunctions.
14. Do not attempt to repair this appliance yourself. In case of damage,
contact authorized service point for check-up or repair. Never
disassemble this device.
15. Clean and store this device in accordance to the instructions listed in
"Cleaning and storage" section.
PRODUCT DESCRIPTION
⑤
④
1.
Adjustable spacer
2.
Blade guard
3.
Fluff compartment
4.
Battery compartment cover
5.
ON/OFF button
6.
Cleaning brush
BATTERY INSTALLATION
1.
Slide out the battery compartment cover.
2.
Insert 2x AA battery with correct polarization.
3.
Slide in the battery compartment cover.
Notes:
•
Use only specified batteries.
•
Do not mix batteries of different type.
•
Replace all batteries at the same time.
•
Store the device without the batteries inside if it is not going to be
used for more than 3 months.
MOUNTING THE ADJUSTABLE SPACER
1.
Place the spacer on the cutting head so that the notches on the spacer
fit into the projections on the cutting head and press it firmly.
2.
Pull the spacer off the cutting head to remove it from the device.
EN
①
②
③
⑥
OPERATION
Notes:
•
Before first use make sure that all parts of the device have been
properly installed and the fluff compartment is empty.
•
You can use the device without the spacer on.
•
This lint remover can damage very soft materials. Therefore always test
the lint remover on an inconspicuous part of the garment.
•
The device will not operate if the blade guard is not installed.
1.
Lay the garment on a flat surface such as an ironing board. Ensure that the
surface to be processed has no wrinkles. Otherwise, the garment could
be damaged.
1.
Set the cutting distance by rotating the spacer left or right or take the
spacer off.
• Upper position (large distance to the blade guard) for large bobbles and
coarse textiles.
• Lower position (small distance to the blade guard) for small lint and fine
textiles.
• Remove the spacer only for very fine lint (no spacing to the blade
guard).
3.
Turn on the device by pressing the ON/OFF button.
4.
Run the device lightly and without too much pressure over the material.
5.
Turn off the device by pressing the ON/OFF button.
6.
Slide out the fluff compartment. Throw away fluff that have been collected
inside the fluff compartment. Replace the fluff compartment and push it
onto the device until it locks in place (you will hear an audible click).
CLEANING AND STORAGE
•
Do not place the appliance in water or any liquid.
•
Do not use any chemical agents to clean this device.
•
Clean this device with a soft, slightly damp cloth.
•
Do not let the fluff compartment being overfilled. If the fluff
compartment is overfilled, the blade will work slowly even though
the batteries are still working. Regularly empty the fluff compartment.
Note: Blade is very sharp and can easily be damaged. Exercise special caution
when cleaning.
1.
Make sure the device is switched off.
2.
If used, remove the adjustable spacer, unscrew the blade guard and
remove the blade. Clean the blade and blade guard with the included
cleaning brush.
3.
After cleaning, put the blade on the spindle and tighten the blade
guard.
•
Before storing, make sure the device is clean and dry.
•
Store the device in a dry, cool place out of the reach of children.
English
Correct Disposal of This Product
(Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier
and check the terms and conditions of the purchase contract. This product
should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k.,
ul. Garwolińska 1, 08-400 Miętne.
Werbung
Inhaltsverzeichnis
