Preset Stations; Aux-In Mode - perfect pro ROCKBULL Benutzerhandbuch

Calling up RDS information
When you are listening to a FM station with RDS system, repeatedly press the INFO
button to cycle through the information. This will only function if the reception level is
sufficient and clear.
a. Station name (PS) Displays the name of station being listened to.
b. Radio text (RT) Displays the message about the station being listened to as
ticker text.
c. Program type (PTY) Displays the type of station being listened to, e.g. Pop,
Classic, News, etc.
d. Frequency Displays the frequency of the station being listened to.
e. Stereo or Mono Displays Stereo or Mono.
f. Signal level Displays the signal strength.
g. Time & date Displays the current time (24 hour clock) and date.
Scan sensitivity setting – FM
The radio will normally scan all stations from FM broadcasts including the weaker
signals. However, you may wish the Auto-scan to find only those stations with strong
enough signals to give good reception.
1. Press the On/Off button to switch on the radio.
2. Select the FM band by pressing the SOURCE button.
3. Press the MENU button, the display shows "Scan Setting".
4. Press the TUNING button.
5. Rotate the TUNING knob to select "All Stations" or "Strong Station" (default is "All
Stations"). The "Strong Station" option will allow the radio to find strong signals only
when scanning.
6. Press the TUNING knob to confirm your setting. The display will return to normal
radio display.
FM stereo / mono
1. If the FM station being received is weak, some hiss may be audible. To reduce
the hiss, press the Mono/Stereo button to switch to mono mode, the display will
show "Mono".
2. To return to stereo mode, press the Mono/Stereo button and the display shows
"Stereo", the radio will switch to stereo mode automatically if the reception is good.
3. "Mono" and "Stereo" can be displayed on the LCD display (See "Calling up RDS
information" above)

PRESET STATIONS

Storing preset stations
There are 20 memory presets in the radio, 10 for DAB and 10 for FM. Presets are
remembered by the radio in the event of a power failure.
9
Press the On/Off button to switch on the radio.
1.
2. Select the desired waveband by pressing the SOURCE button.
3. Tune to the required station.
4. Press and hold the required Preset (1–10) button until the radio beeps and shows
"Saved".
5. Repeat step 3 and 4 for the remaining presets.
6. Stations stored in the preset memories can be over-written again by following the
above procedures.
Recalling preset stations
1. Press the On/Off button to switch on the radio.
2. Select the desired waveband by pressing the SOURCE button.
3. Briefly Press the required Preset (1-10) button. In FM mode the display will show
for example "P1" on top right hand side.

AUX-IN MODE

A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (Aux cable not
included with this radio).
1. Connect an audio source to the AUX-IN socket.
2. Press the SOURCE button to select AUX input. Display will show "AUX IN".
3. Play the external player.
4. Adjust the VOLUME of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover well closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal* from the Aux-In socket for a period of over 15 minutes, the radio will automatically
switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
GB
G B
10