Additional Metal Telescopic Antenna; Language Setting; Software Version; System Reset - perfect pro ROCKBULL Benutzerhandbuch

Press the EQUALIZER button repeatedly to select the desired EQ. The displayed
2.
EQ will be effective immediately:
EQ1 Neutral
EQ2 Indoor
EQ3 Outdoor
EQ4 Flat
EQ5 Rock
EQ6 Soul and Jazz
EQ7 Classical
EQ8 Acoustic
EQ9 Dance
EQ10 Spoken word
EQ11 Small room
EQ12 Late night
3. The display will return to normal in 3 seconds, and resume operation.

ADDITIONAL METAL TELESCOPIC ANTENNA

You can use this as an alternative antenna for your radio in areas or locations where the
radio signal (FM/DAB/DAB+) is weak to very weak.
ATTENTION: The standard antenna on the radio is flexible. The metal antenna
is not flexible or bendable and should be used with care. Breaking or bending
antennas is not covered by warranty.
Installing: Carefully screw off the standard flexible antenna. First carefully loosen the
antenna with an open-end-wrench (size 14) – turn counter anti-clockwise.
Carefully screw on the metal telescopic antenna and softly tighten it with an open-end
wrench key (size 14) – turn clockwise.
ATTENTION: do not use too much force when fixing the antennas as this can
damage the screw threat of the antennas or make it break off.

LANGUAGE SETTING

The menu of the radio can be configured to various languages.
1. Press the On/Off button to switch on the radio.
2. Press the MENU button, and then rotate the TUNING knob until the display shows
"System".
Press the TUNING knob; rotate the TUNING knob until the display shows
3.
"Language".
4. Press the TUNING knob b to enter the language adjustment menu.
5. Rotate the TUNING knob until the desired language appears on the display (default
is English).
6. Press the TUNING knob to confirm your choice.
7. The display menu will then change to the chosen language.
13

SOFTWARE VERSION

The software display cannot be altered and is just for your reference. You can only view
the software version in DAB and FM modes.
1. Press the On/Off button to switch on the radio.
2. Press the SOURCE button to select FM or DAB mode.
3. Press the MENU button and then rotate the TUNING knob until the display shows
"System".
4. Press the TUNING knob; rotate the TUNING knob until the display shows "SW
version".
5. Press the TUNING knob to view the software version.
6. Press the MENU button to return to the normal radio display.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the On/Off button to switch on the radio.
2. Press the MENU button.
3. Rotate the TUNING knob until the display shows "System". Press the TUNING
knob.
4. Rotate the TUNING knob until the display shows "Factory Reset". Press the
TUNING knob.
5. Rotate the TUNING knob to select between "Yes" or "No". Select "Yes" if you wish to
reset the radio, otherwise, select "No".
6. Press the TUNING knob to confirm your choice.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values. The radio will start up and the display
will show "WELCOME TO DIGITAL RADIO" for a few seconds. Then the radio will
automatically perform an auto scan of the Band III DAB channels and the FM band.
The display will show "Scanning" in DAB and "Auto" in FM.
8. When the scan is completed, the 10 strongest FM stations will be stored as presets.
The radio will switch to standby with the updated clock and date showing on the
display.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
reconnect the power supply.

BACKLIGHT

When the radio is in operation or in standby, pressing any button will illuminate the LCD
display for approx. 10 seconds.
GB
G B
14