Functional Description - Makita CL183D Bedienungsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before adjust-
ing or checking function on the tool.
• Take care not to trap finger(s) between cleaner
and battery as shown in diagram when loading
battery.Trapping finger(s) may cause injury.
► Fig.1
Installing or removing battery
cartridge
► Fig.2: 1. Red indicator 2. Button 3. Battery cartridge
CAUTION:
• Always switch off the tool before installing or
removing of the battery cartridge.
• Hold the tool and the battery cartridge firmly
when installing or removing battery car-
tridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your
hands and result in damage to the tool and
battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge align the tongue on the
battery cartridge with the groove in the housing and slip
it into the place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
• Always install the battery cartridge fully until the
red indicator cannot be seen. If not, it may acci-
dentally fall out of the tool, causing injury to you
or someone around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
conditions:
• Overloaded:
The tool is operated in a manner that causes
it to draw an abnormally high current.
In this situation, release the switch trigger on
the tool and stop the application that caused
the tool to become overloaded. Then pull the
switch trigger again to restart.
If the tool does not start, the battery is over-
heated. In this situation, let the battery cool
before pulling the switch trigger again.
• Low battery voltage:
The remaining battery capacity is too low
and the tool will not operate. If you pull the
switch trigger, the motor runs again but stops
soon. In this situation, remove and recharge
the battery.
Switch action
CAUTION:
• Before inserting the battery cartridge into the
tool, always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
► Fig.3: 1. Switch trigger
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Disposing of Dust
CAUTION:
• Empty the cleaner before it becomes too full, or
the suction force weakens.
• Be sure to empty out the dust inside the cleaner
itself. Failure to do so may cause the filter to be
clogged or the motor to be damaged.
► Fig.4: 1. Capsule
In order to drop dust sticking on the filter in the capsule,
tap the circumference of the capsule 4 or 5 times with
your hand.
► Fig.5: 1. Capsule 2. Suction inlet
Now point suction inlet downwards, turn capsule in
direction of arrow in diagram, and disconnect capsule
slowly and straight.
NOTE:
• Dust may spill out when opening capsule. Be
sure to keep capsule as vertical as possible,
and place a garbage bag beneath capsule.
► Fig.6: 1. Prefilter 2. Capsule
Remove accumulated dust from inside of capsule and
off of prefilter.
► Fig.7: 1. Prefilter 2. Securing lip
Twist prefilter in direction of arrow to unfasten securing
lip from cleaner unit and then pull off prefilter.
► Fig.8: 1. Prefilter 2. Filter
Clean out fine dust from prefilter. Next, remove filter,
and lightly tap to dislodge dust.
7 ENGLISH