Uk: Instructions - LEGO Technic 8299 Bedienungsanleitung

U K
Some Important Information
The LEGO ® Software on this Disc is the result of a great deal of work.
To help us bring you high quality programs in the future it is important
as a legal requirement to read the following:
First Rule:
Following the purchase of the LEGO program you are permitted to copy
the program to your own computer. However, it is illegal to allow other
users to gain access to your program either via the Internet or by
uploading the program to a network from which it can be copied. It is not
a problem should you lose the original but have the program copied on
your computer.
Second rule:
If you sell or pass the program on it is illegal to use the program yourself.
It is also illegal to lend or rent computer programs.
It is important to know that the LEGO trademarks should not be used
®
freely. An or a ™ following a name identifies the name as being a
trademark.
If you need to know anything else about the legal requirements, then
more information can be found on the CD-ROM. If you are connected to
the Internet you can also look at our homepage on http://www.LEGO.com
for more information about the use of the trademarks of the LEGO Group.
Instructions
Apple Users
1. After inserting the LEGO CD-ROM into the machine, double click on
the LEGO icon and then on the icon called LEGO Setup to install the
CD-ROM on your computer.
2. A "LEGO" folder will be created at the top level of your boot-up drive.
This folder will be used to store user names, "book-marks", and temporary
files. You should have 10MB free on your hard drive for this folder.
3. This LEGO Software requires QuickTime and/or SoundManager.
If installation is required then the LEGO CD-ROM will have to be
restarted.
4. Next time you want to use your LEGO CD-ROM, insert the CD-ROM into
your machine, go to the LEGO folder (LEGOTECH) on your harddrive and
double click on the Start PPC/Start 68k icon.
Windows 3.11 Users
1. Make sure Windows 3.11 is running.
2. Check that your CD-ROM and sound card drivers are loaded.
3. After inserting the LEGO CD-ROM, use either the File Manager
program (look in Group MAIN in the Program Manager) or BROWSE and
click on the letter of your CD-ROM drive (usually "D").
4. Double click on the SETUP.EXE program.
5. This LEGO software requires QuickTime for Windows. If installation is
required then the LEGO CD-ROM will have to be restarted.
6. Points 3, 4 and 5 only occur the first time you run the LEGO CD-ROM.
7. Double click the LEGO Icon in the LEGO TECHNIC Program Group to
run the LEGO CD-ROM.
Windows 95 Users
1. Your Windows 95 package should start up automatically. Check that
your CD-ROM and sound card drivers are loaded.
2. After inserting the LEGO CD-ROM into your drive wait for the Autoplay
screen to appear and then click on the OK button to continue.
3. Follow the instruction which may require you to install QuickTime for
Windows, if not already installed. If installation is required then the
LEGO CD-ROM will have to be restarted. The next time you want to use
the LEGO CD-ROM, you can simply insert the CD-ROM.
Additional Notes for Windows 3.11 and 95 Users
The LEGO CD-ROM creates a directory called LEGO on the boot drive of
your computer. This directory will be used to store user-names, "book-
marks", and temporary files. You should have 10MB free on your hard
drive for this directory. Don't panic if you accidentally delete this
directory.
The LEGO CD-ROM will create a new one if it doesn't find the original
one, however, you will have lost your bookmarks and saved user-log files.
4
Trouble shooting
Windows 3.11 Users
GPF (General Protection Fault): Usually this error is caused by the video
driver conflicts. If you experience this error, try installing the SVGA 640
by 480, 256-colour driver.
If your colours still look strange, make sure that your video drivers and
monitor are capable of displaying 256 colours and are configured to do so.
Windows 95 Users
If you do not see the "AutoRun" screen after you insert the CD-ROM,
please use the right-hand mouse button to "Open" the CD-ROM and then
double click on the LEGO_CD.SCP icon.
Apple Users
If you experience problems, please disable Virtual Memory or RAM
Doubler if you are running either of these. As a last resort, use Extensions
Manager to restart your computer with only the QuickTime extension
running (selecting System 7.x from the Extension Manager menu should
configure your computer to be compatible with the LEGO CD-ROM in any
case).
User Guide
Introduction
Welcome to the LEGO TECHNIC Underwater Base! The base has five
rooms:–
3 FOR CONSTRUCTING MODELS
1 BRIEFING ROOM
1 SHOWROOM
This guide will help you, but you can experiment yourself by clicking onto
any button to see what it does. The guide may give you some useful hints
and information which will make your visits to the base more interesting.
Just dive in and have fun!
General control panel functions
When you start up the program, you will see a log-in screen where you will
be asked to type in your log-in name and choose a language. When you
have done this, click the OK button. The LEGO TECHNIC logo will then
appear on your screen and then the intro-animation will begin. If you have
entered your name earlier, you can just click on it and then click the OK
button. The program can have up to five different users. Each can have
their name on the log-in screen. (The program will save separate settings
and bookmarks for each of the five users). After the intro-animation ends
you will find yourself in the Submarine Room. If you click on the intro-
animation you can skip this intro.
The left and middle part of the control panel is the same in all five rooms,
the right side of the control panel changes according to which room you
are in. The general controls are:–
Q QUIT BUTTON. Exits the program.
W MAIN BUTTON. Clicking this button restarts the program.
E This is the SETTINGS-BUTTON. Clicking this will reveal the buttons
for controlling the GENERAL SETTINGS:–
3a
Volume down / up
3b
Text 'Telex' Off / On
3c
Diver video link Off / On
3d
Switch between languages
3e
Cancel
3f
OK
R PRINT BUTTON. By pressing this button, once you have built your
model, it will print out your diploma provided you are linked to a printer
and have the necessary driver(s) present.
T ROOM NAVIGATOR. This shows a small 'map' of the Underwater Base
where you can click on the room you want to visit.
Y Video-link to the diver who will help you out from time to time.
You can stop the video link by clicking on the diver.
U Repeats the last message from the Diver.
I Displays the building time in the information display.
If you click it again the timer will disappear. If you have the timer visible,
the building time will appear on your diplomas when they are printed.