Intended Use - Makita DRV150 Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Pulling force
Stroke
Overall length
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for installing blind rivet.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-1:
Model DRV150
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DRV250
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
) : 75 dB(A)
pA
) : 74 dB(A)
pA
DRV150
10 kN
25 mm
313 mm
1.9 - 2.2 kg
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-1:
Model DRV150
Work mode: Installing blind rivet
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DRV250
Work mode: Installing blind rivet
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
DRV250
20 kN
30 mm
323 mm
D.C. 18 V
2.1 - 2.4 kg
DC18SH
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2