jedo LARK Bedienungsanleitung Seite 12

USER'S MANUAL
1. ASSEMBLING THE STROLLER
The unfolding of the stroller is performed by pulling
the handle up, when it reaches the correct position, it
automatically locks in a locking clamp, accompanied by a
clearly audible „click" sound.
2. ATTACHING AND REMOVING THE WHEELS
To remove rear wheels, press the button on the inside of
the frame (in front of the brake) (Photo no.1) and remove
the wheel along with the axle. Repeat for the other side.
To re-attach, push the button for disengaging the wheels
and push the wheel axle into the hole in the frame. (Pho-
to no.2). Then release the button and pull them together
until they lock.
- Install the front 10 „wheel with the fork, by inserting the
axle forks into the rotary element, until you hear a click of
the wheel locking into its correct position.
The front wheels may be locked to run straight-ahead
only, by turning the lock mechanism of wheels located on
both sides of the frame, under the footrest (Photo no.4)
to the left (looking from the handle) until it clicks.
To remove the front wheel, press the gray button on the
inside of the frame, just below the rotary element locking
the front wheels (Photo no.3)
WARNING! The wheels are covered with a lubricant,
which may stain textiles.
3. ENGAGING THE BRAKES
The stroller is stopped by pressing the brake pedal, posi-
tioned at the right wheel (handle side – Photo no. 5).
Release the brake by pushing the identical brake pedal,
positioned at the left wheel.
4. ASSEMBLY / REMOVAL OF THE CARRY COT.
Assemble the carry cot on the chassis by inserting the
plastic carry cot adapters, located in its lower part,
into the central locking mechanism. Locking will occur
automatically. To remove the carry cot, press buttons
simultaneously on both sides of the carry cot (Photo
no.6), then lift the carry cot up.
WARNING! Before use, check if the carry cot is properly
locked in the central locking mechanism.
5. INSTALLATION OF THE FOOT COVER
Put the foot cover on the carry cot and fasten using the
press-studs on the sides of the hood and the cover.
- The „T" line extendable cover element must be clipped
to the booth by means of magnets in its interior.
- The „R" line extendable cover element may be clipped
to the booth with a magnet located at the top of the hood,
under the sun-roof.
6. ADJUSTING THE BACKREST OF THE CARRY COT
Adjusting the backrest is done by means of a regulating
element, positioned underneath the carry cot, at the level
of the backrest (Photo no. 7). To raise the backrest, gen-
tly press the element and lock the backrest in the desired
position, by moving it forward or backward.
7. THE ROCKER FUNCTION OF THE CARRY COT
To use the carry cot's rocker function, move the two roc-
ker elements located at the bottom of the carry cot from
the horizontal position to the vertical position (Photo no.
8 a,b).
8. SETTING THE CARRY COT VENTILATION
To change the carry cot ventilation, move the ventilation
control located on the bottom of the carry cot to the right
or to the left (Photo no. 9).
9. REMOVAL OF THE CARRY COT
To remove the carry cot, remove the material inside the
carry cot to reveal the hidden mechanism of the carry
cot (Photo no. 10), then move the 4 folding mechanisms
towards the center part of the carry cot (Photo no. 11).
To remove the carry cot, the mechanisms must be moved
to their folding position.
10. SEAT ASSEMBLY (STROLLING INSERT)
The seat assembly and disassembly is performed similar
to the carry cot, with two buttons located on both sides
of the seat. The seat can be installed in two ways - facing
forward or rearward.
WARNING! Do not carry the seat by grasping the
footrest!
WARNING! Before use, check if the seat is properly
locked in the central latch.
WARNING! Before using the stroller, always check whe-
ther the backrest is properly locked.
11. INSTALLATION / REMOVAL OF SEATS HOOD
The seat is equipped with its own hood, in order to
mount it on the seat, insert the plastic hood-fastening
elements located at the ends of the rod (Photo no.12)
into plastic connectors located on both sides of the
backrest. (Photo no. 13). To remove the hood, press the
button on the hood-fastening element, then pull the rod
upwards.
12. INSTALLATION / REMOVAL / RAIL HEIGHT ADJU-
STMENT
Mount the safety rail by placing the element for rail
mounting in the connectors (Photo no. 14).
In order to remove the rail, press the gray button located
on both sides of the seat at the height of the rail (Photo
no.15 A), then pull it towards you.
To change the height of the rail, press the red button
(Photo no. 15 B), located on both ends, then set the desi-
red height of the railing. Locking in the selected position
happens automatically.
13. ASSEMBLY OF FEET COVER (Seat)
Stretch cover on the seat and attach using press-studs.
14. ADJUSTING THE BACKREST OF THE SEAT.
The backrest of the seat can be set in several positions.
To lower the backrest, pull the plastic regulation element
located in the rear of the backrest, then set the correct
position. (Photo no.16)
WARNING!! The same button is used to fold the seat in
half; in order to do that, press the button described above
a little longer and move the backrest of the sear toward
the front. This operation is performed after prior disman-
tling of seat hood (not applicable to the R line).
To raise the backrest, simply push it upwards until you
reach the correct position. Locking will occur automati-
cally.
15. SETTING THE FOOTREST POSITION / ADJUSTING
THE LENGTH
The footrest can be adjusted in several positions. To
lower it, press the two buttons located on both sides of
the footrest and gently lower it down. (Photo no. 17).