Inhaltsverzeichnis
Werbung
GB
•
Warning: The wheel still rotates after the
machine has been switched off
•
Hold the machine by the insulated grips when
performing an operation where contact can be
made with hidden wiring or its own cord.
•
Before use, inspect the disc for any damage.
Do not use discs which are crack-ed, ripped
or otherwise damaged.
•
Before use, let the machine run idle for 30
seconds. Immediately switch off the machine
in case of abnormal vibrations or occurrence
of another defect. Carefully inspect the
machine and disc before switching the
machine on again.
•
Always wear safety goggles and hearing
protection.
•
Ensure that mounted wheels and points are
fitted in accordance with the manufacturer's
instructions.
•
For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the
wheel is long enough to accept the spindle
length.
•
Ensure that ventilation openings are kept
clear when working in dusty conditions. If it
should become nessesary to clear dust, first
disconnect the tool from the mains supply
(use non metallic objects) and avoid
damaging internal parts.
•
Though poor conditions of the electrical
mains, shortly voltage drops can appear when
starting the equipment. This can influence
other equipment (eq. blinking of a lamp). If the
mains-impedance Zmax <0.348 Ohm, such
disturbances are not expected. (In case of
need, you may contact your local supply
authority for further information.
Electrical safety
When using electric machines always observe
the safety regulations applicable in your country
to reduce the risk of fire, electric shock and
personal injury. Read the following safety
instructions and also the enclosed safety
instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated;
therefore no earthwire is required.
06
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Assembling the handle
Fig. 2
The handle is suitable for either left or right-
handed use.
•
Install the handle in such way that the holes
match the screwholes on the machine.
•
Tighten the handle with the bolts and hexagon
key.
Assembling accessoires
Fig. 3
•
Press the spindle lock
•
Screw and tighten the pad holder on the spindle
•
Depress the spindle lock
•
Mount the polishing pad onto the pad holder.
Accessoires
Fig. 4
Pattern felt (1)
This is used for sanding and polishing new paints
and plastics.
Fiber pad (2)
This is used in combination with other pads.
Polishing pad (3)
In combination with the fiberpad, this is used for
high lustre polishing and waxing. The plastified
layer inside assures the maximum use of the
used wax.
Wool polishing pad (4)
This is used for a high gloss finish. To be used in
combination with the fiber pad.
Ferm
Rengøring
Ventilationsrillerne skal holdes rene for at
forhindre, at maskinen overophedes.Maskinens
kabinet skal jævnligt renses med en blød klud,
helst efter hver brug. Hold ventilationsrillerne fri
for støv og snavs. Hvis snavset ikke vil gå af,
anvendes en blød klud fugtet med sæbevand.
Anvend aldrig opløsningsmidler som benzin,
sprit, salmiakspiritus etc. Disse opløsningsmidler
kan beskadige plasticdelene.
Fejl
Skulle der opstå en fejl, f. eks. ved nedslidning af
en del, skal du kontakte serviceadressen på
garantikortet. I slutningen af denne vejledning
findes et udvidet afsnit, der viser hvilke dele der
kan bestilles.
Miljø
For at forhindre, at maskinen beskadiges under
transport leveres den i en solid emballage, der
fortrinsvis består af genanvendeligt materiale.
De bedes derfor udnytte mulighederne for, at
emballagen genbruges.
Defekt og/eller kasseret elektriske eller
elektronisk udstyr skal indsamles og
afleveres til en genbrugsstation.
Garanti
Garantibetingelserne er anført på det
medfølgende separate garantikort.
Ferm
DK
43
Werbung
Inhaltsverzeichnis
