Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
make sure that voltage in your mains corre-
sponds to the base operating voltage.
Place the base (9) on a flat stable surface,
–
away from moisture and heat sources and
direct sunlight.
Note: - You can mount the base (9) on the wall.
Attention!
Before drilling holes in the wall, make sure
–
that there is no electrical wiring at this place.
When mounting the base on the wall, place
–
it above the socket and provide easy access
to the socket.
Mark the position of holes on the wall.
–
Drill the holes in the wall to the required
–
depth.
Insert plastic dowels into the holes and drive
–
the screws into them.
Mount the base (9) on the wall.
–
Place the vacuum cleaner on the base (9).
–
Battery charging
Suction power of the vacuum cleaner
decreases significantly when the battery is low;
in this case, recharge the battery .
Before recharging the battery for the first
–
time, discharge it completely (the vacuum
cleaner cannot be switched on in this case).
Place the base for vacuum cleaner charging/
–
storing (9) on a flat steady surface or mount
it on the wall.
Insert the power plug into the socket, the
–
indicator (10) will start flashing.
Place the vacuum cleaner on the base (9),
–
the indicator will stop flashing and light con-
stantly.
The indicator (10) will go out when the battery
–
charging is finished.
Pull the power plug out of the socket after the
–
battery charging.
Always unplug the base after battery charging.
–
Note: - If the indicator (10) continues flashing
when you place the vacuum cleaner with a
fully discharged battery on the base (9), press
the on/off button (5) again, in approximately
5 seconds after that the indicator (10) will
light constantly, indicating start of battery
recharging.
Additional requirements
•
Perform the first three battery recharging
cycles only after the battery is totally dis-
MW-3241.indd 8
charged (the vacuum cleaner cannot be
switched on).
•
Average duration of battery charging is from
8 to 14 hours.
Attention! Do not remove the vacuum
cleaner from the base during the battery
charging, wait till the battery is fully
charged, the indicator (10) goes out.
Operation
Safety measures
•
Do not use the vacuum cleaner near hot
surfaces, ashtrays and in the places where
inflammable liquids are stored.
•
Take sharp objects away before cleaning to
prevent unit damage.
Attention! Always use the vacuum cleaner
only with the installed filters (2, 3) in the
dustbin (1) and check if the filters (2, 3) are
installed properly.
–
Recharge the battery and unplug the base.
Remove the vacuum cleaner from the base
–
(9).
Install the required attachment (7 or 8) into
–
the dustbin (1) opening.
Switch the vacuum cleaner on/off by press-
–
ing the on/off button (5).
Using the brush attachments
Small brush (7)
The small brush (7) is intended for collecting
dust, the pile prevents the damage of polished
furniture surface.
Crevice nozzle (8)
The crevice nozzle (8) is intended for cleaning
of radiators, chinks, corners etc.
Keep the attachments (7, 8) on the base (9).
–
Cleaning and care
Remove garbage and dust, clean the dustbin
(1) and the filters (2, 3) after each use of the
vacuum cleaner.
Start cleaning only after removing dust and
garbage from the dustbin (1).
Detaching of the dustbin (1) and removing
of dust and garbage from it
−
Switch the vacuum cleaner off.
−
Press the release button (4) and remove
the dustbin (1) (fig. 1).
−
Place the dustbin (1) above the garbage
bin; remove the filters (2, 3).
8
19.11.2013 10:56:44
Werbung
