Important Safety Information - Hatco SeRv-Rite SRB Series Installations- Und Bedienungshandbuch

Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property
WARNING
eLeCtRiC ShOCk hAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. if
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOt submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Do not steam clean or use excessive water on unit.
• this unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by hatco, an Authorized
hatco Service Agent, or a person with similar
qualifications.
• Never overload extension cord. Use heavy duty, three-
wire extension cord only. Make sure current carrying
capacity of extension cord complies with electrical
rating of unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• Do not fill SRB and SRBW models with water. they are
dry heat units only, not steam table units.
• Use only Genuine hatco Replacement Parts when
service is required. Failure to use Genuine hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in hatco equipment.
FiRe hAzARD: Locate unit a minimum of 25 mm (1") from
combustible walls and materials. if safe distances are not
maintained, combustion or discoloration could occur.
Use only low pressure halogen light/heat lamps that meet
or exceed National Sanitation Foundation (NSF) standards
and are specifically designed for food holding areas.

iMPORtANt SAFety iNFORMAtiON

Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure
to heat food product properly may result in serious health
risks. this unit is for holding preheated food product only.
Make sure all operators have been instructed on the safe
and proper use of the unit.
this unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
ensure proper supervision of children and keep them away
from the unit.
this unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
this unit has no "user-serviceable" parts. if service is
required on this unit, contact an Authorized hatco Service
Agent or contact the hatco Service Department at
414-671-6350; fax 414-671-3976.
BURN hAzARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Make sure to clean and sanitize the stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
Do not lay unit on the side with the control panel or damage
to the unit could occur.
Use non-abrasive cleaners on glass and metal surfaces.
Abrasive cleaners could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Do not slide pans across glass surface, use rough-
bottomed pans, or drop anything on glass surface.
Scratching or breakage may occur. Damage to glass
surface or breakage of glass caused by misuse is not
covered under warranty.
Do not place anything on top of glass sneeze guard. it is
not designed to be a weight-bearing component.
Do not attempt to install glass sneeze guard alone.
installation of glass sneeze guard is a two-person job.
Do not move unit by lifting or pulling it by the sneeze guard.
Do not touch halogen heat lamps with bare skin. Oils from
the skin will cause premature failure of the lamps.
.
WARNING
CAUTION
NOTICE