Features And Functions - Tomy TSP500 Bedienungsanleitung

• GETTING TO KNOW YOUR MONITOR
Your Tomy Movement Sensor Pad Monitor TSP500 has been carefully designed to sit underneath the mattress of your
cot or Moses basket to detect all movements baby makes and to emit an alarm when no movement is detected after
20 seconds.
Every movement is accompanied by a soft click and an illuminated visual indicator. Should no movement be
detected on the Movement Sensor Pad for 20 seconds, a continual beep alarm will be activated.
Movement Indicator
Volume Control
Wheel
Cable Tidy
ON/OFF
Button
Tomy Digital Monitor Range (see 'Portable Monitoring')
• SET UP
• POSITIONING THE MOVEMENT SENSOR PAD TSP500
The Tomy Movement Sensor Pad TSP500 sits underneath the mattress of your cot or Moses basket as shown (below).
Once you have chosen baby's sleeping area, position the Movement Sensor Pad to lie directly underneath her torso.
IMPORTANT! The Movement Sensor Pad must rest on a completely flat, rigid surface and must be placed with the 'Tomy
logo' side facing up. Ensure that no bedding is positioned between the mattress and the Movement Sensor Pad.
For best performance we recommend covering the base of slatted based cots with a thin layer (6mm) of plywood to
ensure an even surface. Ensure any loose cable is wrapped and tied to avoid possible entanglement. From the cot, run
the cable along the floor ensuring it is kept out of baby's reach; excess cable should be spooled around the cable tidy.
GB
Input for second
Connection Cable
Connection cable for the
Keep cot sides & ends at
least 38cm (15 inches)
from adjacent bedroom
furniture
2

• FEATURES AND FUNCTIONS

• PAD CONTROLLER
Movement
Sensor Pad
• CONNECTING THE PAD TO THE CONTROLLER
• TESTING
Before every use we recommend carrying out the following checks with the Pad in the cot or Moses basket (as per the
Set Up guide). Firstly tap the mattress, at which time the Pad Controller should emit a soft click and the
shall flash Green. Follow this by leaving the Pad to stand untouched for 20 seconds, then the alarm
shall sound and the indicator shall illuminate red. Simply deactivate the alarm by tapping the mattress again.
• PAD CONTROLLER VOLUME WHEEL
The volume of the soft click can be adjusted using the volume control wheel on the Pad Controller from mute to max.
Move the thumb wheel clockwise to increase or anti-clockwise to decrease.
You can also monitor baby's movement without the movement click by turning the Volume Control Wheel to the
mute position, and observing the movement indicator on the Pad Controller that also accompanies every movement
(just like the click).
Please be assured that during mute mode, the no movement alarm shall be unaffected and the continual bleep alarm
will sound if no movement is detected for 20 seconds.
• LOW BATTERY ALARM
The Pad Controller will emit a 4 'beep' alarm every 60 seconds and the
batteries need replacing.
• ADDITIONAL MOVEMENT SENSOR PAD
To monitor a larger surface area within the cot, the supplied Movement Sensor Pad has been designed to connect to
another Tomy Movement Sensor Pad. For further details, please visit our website; www.tomy.eu
GB
The Pad Controller is solely battery operated and requires 4 x AA (LR06) batteries
(not supplied). Insert batteries by removing the battery compartment cover on
the underside of the unit using a flat headed screw driver. Insert the batteries
ensuring correct polarity and replace the cover, screwing firmly into position.
To activate the Pad Controller, press and hold the
green.
Connect the Movement Sensor Pad cable to the
Controller. To ensure that the product is as reliable as possible Tomy have
developed locking connectors for the cables between the Pad and Pad Controller
(and Pad Controller and Portable Monitor). When connecting, push the
connector plug into the socket until the locking arm of the plug clicks. To release
the plug, firmly squeeze and pull the plug so that the locking arm is released
from the socket.
button shall flash red, indicating that the
3
button until it illuminates
socket on the Pad
indicator