Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EN
1 - SAFETY WARNINGS
CAUTION – to ensure personal safety it is important to follow these instructions and
keep them for future reference.
Read the instructions carefully before proceeding with installation. The design and manufac-
ture of the devices making up the product and the information in this manual are compliant
with current safety standards. However, incorrect installation or programming may cause
serious injury to those working on or using the system. Compliance with the instructions
provided here when installing the product is therefore extremely important.
2 - INTRODUCING THE PRODUCT
XR MANAGER is a hand-held programmer that can be used with the Key Automation XR
Rolling Code transmitter series.
This system speeds up the programming phase and simplifies memorisation of new transmit-
ters, while maintaining the security of the rolling code system.
The transmitters and receivers in the series XR (for example receivers RX4X, RXM23X with
firmware version 2.3 and later) are designed to exchange information via radio. In particular,
the ROLLING CODE TRANSMITTERS WITH INCORPORATED RECEIVER (code numbers
ending in "F" and amber led, e.g. SUB44F) contain a proximity receiver that enables the
memorisation of an AUTHORISATION CODE sent by a transmitter previously memorised
on the system.
The authorisation code acquired then enables the transmitter to be memorised by the re-
ceiver on the automation, automatically and without the need to access the receiver itself.
Also, this series of transmitters, receivers and the hand-held device XR MANAGER, users
can manage a large number of transmitters on a single system, for example replacing or
adding transmitters without the need to be on site.
Caution: Any other use than as specified herein or in environmental conditions other
than as stated in this manual is to be considered improper and is strictly prohibited.
CODE
DESCRIPTION
XRMAN
XR MANAGER programmer for XR Rolling Code
TECHNICAL SPECIFICATIONS
Receiver compatibility
Power supply
Maximum absorption
Operating temperature
3 - PRODUCT INSTALLATION
Enable navigation of the menus and selection of parameters.
Press and hold button
(4 seconds) to power up the device.
Press and hold button
(2 seconds) to run the back function in the menu.
Press and hold button
(2 seconds) to confirm parameters during settings.
Press and hold button
(>4 seconds) to shut down the device.
3.1 - OPTIONS
XR MANAGER LANGUAGE CHANGE
This function enables the user to change the language on the device used.
OPTIONS
LANGUAGE
CONTRAST ADJUSTMENT
This enables adjustment of the device display contrast
OPTIONS
BRIGHTNESS
XRMANAGER FIRMWARE VERSION
This enables the user to check the current firmware version of the device
OPTIONS
FIRMWARE
3.2 - RECEIVERS
TRANSMITTER TEST
This serves to test operation of a transmitter and view the relative data
RICEIVERS
TEST TRANSMITTER
RECEIVER CODE READING
This menu is used to view the codes memorised on the receiver with the relative slot in the
memory and associated function
RICEIVERS
READ CODES RECEIVER
POSITION
N.0001
TX CODE
0800035
A= BUTTON 1, B= BUTTON 2, C= BUTTON 3, D= BUTTON 4, M= DEFAULT MODE
SEARCHING FOR A CODE IN THE MEMORY USING A TRANSMITTER
Enables the user to search for a transmitter in the receiver memory and to find the position
where the transmitter has been memorised
RICEIVERS
FIND CODE
ADDING A NEW TRANSMITTER TO THE RECEIVER MEMORY USING A
TRANSMITTER
Enables the user to add a transmitter to the receiver memory and to find the position where
the transmitter has been memorised
ADD
RICEIVERS
CODE
XRMAN
RX4X/RXM23X (version 2.3 and later)
3 Vdc
200 mA
-20°+55° C
OUT 1
OUTPUT
IN A
BUTTON
INPUT WITH
TRANSMITTER
ADDING MULTIPLE TRANSMITTERS CONSECUTIVELY TO THE RECEIVER
MEMORY
Enables the user to save a transmitter in the receiver memory of transmitters sequentially
from an initial code
ADD
RICEIVERS
CODE
DELETING A CODE FROM THE MEMORY USING A TRANSMITTER
Enables the user to delete a transmitter from the memory using the transmitter itself
CANCEL
RICEIVERS
CODE
MANUAL DELETION OF A CODE FROM THE MEMORY
Enables the user to delete a transmitter from the memory by scrolling through the list of
codes present in the receiver memory
CANCEL
RICEIVERS
CODE
REPLACING A CODE IN THE MEMORY USING A NEW TRANSMITTER
Enables the user to replace a code in the memory with the new code of a transmitter
REPLACE
RICEIVERS
CODE
COPYING A RECEIVER MEMORY ONTO AN SD CARD
Caution: the SD CARD must be formatted as .fat
Enables an entire back-up copy of the memory of a receiver onto an external memory (SD CARD)
COPY
RICEIVERS
MEMORY
PROGRAMMING THE RECEIVER WITH A DATABASE
Caution: the SD CARD must be formatted as .fat
Enables insertion of a database/backup memory previously created on a receiver
COPY
RICEIVERS
MEMORY
PROGRAMMING THE RECEIVER OUTPUTS
Enables programming of single outputs of the receiver in monostable, bistable, and timed
mode
RICEIVERS
RECEIVER OUTPUTS
MEMORY BLOCK/UNBLOCK
Enables blocking/unblocking of the receiver.
If the receiver is blocked (parameter set to 1) it will not be possible to modify the data present
on the receiver without knowing the serial number of the latter, which is requested on access
to the receiver menu.
The receiver will only be enabled on entry of the codes via certificate and by replacing codes
RICEIVERS
LOCK/UNLOCK MEMORY
CHECKING RADIO NOISE PRESENT IN THE VICINITY
This function enables the user to check the radio noise level present in the vicinity(low/
medium/high)
RICEIVERS
TEST RADIO NOISE
RECEIVER DATA
This menu enables the user to check the firmware version of the receiver and display the
relative serial number
RICEIVERS
RECEIVER DATA
RECEIVER RESET
This function enables the user to restore the default settings to the receiver
RICEIVERS
RESET RECEIVER
3.3 - TRANSMITTERS
STORAGE WITH
TRASMETTERS
TRANSMITTER CODE
INSERTING A TRANSMITTER VIA THE TRANSMITTER CODE
(REMOTE MEMORISATION)
This function enables the user to enter a new transmitter by means of the serial number of
a previously memorised transmitter. The functions of the new transmitter will be identical to
those of the transmitter already memorised on the receiver
INSERTING A TRANSMITTER VIA THE RECEIVER SERIAL NUMBER
(REMOTE MEMORISATION)
This function enables the user to enter a new transmitter by means of the serial number of
the receiver. It is possible here to associate the functions of the outputs or to select the default
settings (button A output 1, button B output 2, button C output 3 and button D output 4)
STORAGE WITH THE SERIAL
TRASMETTERS
NUMBER OF RECEIVER
REPLACING A MEMORISED TRANSMITTER VIA A NEW TRANSMITTER
(REMOTE REPLACEMENT)
This function enables the user to replace a code stored in the receiver memory with a new
one by means of the code of the transmitter already stored in the receiver memory
REPLACEMENT WITH
TRASMETTERS
TRANSMITTER CODE
MULTIPLE
INPUT
DELETE CODE WITH
TRANSMITTER
DELETE
MANUALLY
REPLACE CODE WITH
TRANSMITTER
FROM RECEIVER
TO SD CARD
FROM SD CARD
TO RECEIVER
Werbung
