Kyocera DF-650 Installationsanleitung
Vorschau ausblenden
Andere Handbücher für DF-650:
- Bedienungshandbuch (176 Seiten) ,
- Einführungshandbuch (176 Seiten)
Verwandte Anleitungen für Kyocera DF-650
Inhaltszusammenfassung für Kyocera DF-650
- Seite 1 INSTALLATION GUIDE FOR THE FINISHER GUIDE D’INSTALLATION POUR LE RETOUCHEUR GUIA DE INSTALACION PARA EL FINALIZADOR INSTALLATIONSANLEITUNG FÜR FINISHER GUIDA ALL’INSTALLAZIONE DELLA FINITRICE フィニッシャ設置手順書 DF-650...
-
Seite 3: Supplied Parts
E Sponge ............ 1 English F Staple cartridges........2 Supplied parts G Staple cartridge (100V model) ....1 H M4 × 20TP Tap Tight S screws ....2 A Finisher............ 1 B Main tray..........1 I Nuts ............2 C Sub tray ........... 1 J Pins ............ - Seite 4 Procedure 1. Use the two M4 x 20TP Tap Tight S screws 2. As shown in the illustration, adhere the (H) to secure the connecting plate (D) on the sponge (E) to the top cover of the finisher (A) Before installing the finisher, turn the copier off copier’s output cover (1).
- Seite 5 3. Open the front cover. 5. Remove the screw (5) to pull out the con- 4. Remove the screw (2). Pull up the connect- necting rail (6) at the upper part of the fin- ing lever (3) to lower the hooks (4). isher (A).
- Seite 6 6. Cut out the hole covers (7) at two locations on the copier. 9. Pressing down on the connecting rail (6), 7. Position the finisher (A) and the copier so the long pin (8) of the connecting plate (D) aligns with secure it with the screw (5) you removed in the back hole (9) of the finisher, and the two short pins (10) align with the holes (11) of the con- step 5.
- Seite 7 10. Secure the link lever (3) with the screw (2) 11. Remove the four blue screws (12) locking 13. Remove the fixing tape (16). you removed in step 4. each of the two separate retainers (14) to the intermediate tray (13) and detach both retainers (14).
- Seite 8 14. Remove the fixing tape (17) inside the fin- 15. Raise the release handle (15) to open the 16. Load two staple cartridges (F) into the staple isher. intermediate tray (13). Remove the four holders (19) and (20), and press down on strips of fixing tape (18).
- Seite 9 17. Load the staple cartridge (G) into the staple 19. Insert the two nuts (I) into the main tray (B). holder (21) on the back of the intermediate 20. Secure the main tray (B) with two pins (J). tray (13), and push up on it until it locks 21.
-
Seite 10: Papierwellen Korrigieren
22. Connect the signal cable (23) to the connec- Correcting Paper Curling If the Paper Curls Downward (figure “a”) tor of the copier. 1. In the non-sort mode, run paper through the 23. Plug the copier’s power cable into an outlet 1. - Seite 11 4. Run paper through the machine and check if If the Paper Curls Upward (figure “b”) 3. Rotate the upper lever (27) by one scale in it is still curled downward. 1. Open the front cover. the direction of the larger numbers. 5.
-
Seite 12: Mittelfalt-Heften Korrigieren (Nur Für Multi-Finisher)
5. Run paper through the machine and check if Correcting centerfold-stapling (for multi finisher only) it is still curled upward. 1. Perform test copies using various paper types. Configure the printer for saddle stapling and output 6. Repeat steps 1 to 5 until the ejected paper to the main tray. - Seite 13 3. If the staple position is misaligned, enter 5. Adjust the setting value for each paper size. If the paper is stapled too far toward the paper eject side (as shown in “c” in the illustration), maintenance mode U248 and perform the decrease the setting value.
- Seite 14 MEMO...
- Seite 15 MEMO...
- Seite 16 2005. 2 303H381010...