Symbols; Operating Instruction; Cleaning And Maintenance - MaxPro PROFESSIONAL MPSG400/800V Handbuch

• High pressure at the nozzle.
Recommenda Wear a breathing mask and safety glasses when spraying.
CAUTION - DANGER OF INJURY!
Never point the spray gun at yourself, at other people or at animals.
• When working with the tool indoors as well as outdoors ensure that no solvent vapors are sucked in by
the spray gun.
• When working outdoors, be aware of the wind direc
greater distances - thus causing damage. When working indoors, provide for adequate ven a
• Do not let children handle(4) the device.
• Never open the device yourself in order to carry out repairs in the electrical system!
• Do not lay the spray gun.
Residual risks
Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The
following hazards may arise in c
1. Damage to lungs if an eff ve dust mask is not worn.
2. Damage to hearing if eff ve hearing prot
3. Damages to health r from vibra
ately managed and properly maintained.
WARNING! This power tool produces an electromagne c field during opera
some circumstances interfere with ve or passive medical implants. To reduce the risk of serious or fatal
injury, we recommend persons with medical implants to consult their physician and the medical implant
manufacturer before opera

SYMBOLS

Read the manual
Warning
Double isulation
Wear eye protection

OPERATING INSTRUCTION

Prepara (Fig.1)
Do not use textured wall paints or c
To obtain the best results, it is important that you prepare the surface to be sprayed and thin the paint to
the correct viscosity, before you operate your spray gun. Always ensure that the surfaces to be sprayed
are free from dust, dirt and grease. Make sure that you have masked the areas that should not be sprayed,
using a good quality masking tape. The paint or fluid to be sprayed should be thoroughly mixed and free
from lump ny substances can be sprayed with your spray gun, but always check the
manufacturers recommenda efore purchasing your paint.
Thinning
Always remember to disconnect from the mains supply before filling the paint container (5)with spray able
material.
Most paints are supplied ready for brush applica
to be sprayed. Follow the manufacturer's advice on thinning the paint when used with a spray gun. The
viscosity cup will help you to determine the correct viscosity of paint to be used. The table below shows
4
Wind can carry the coa g substance across
ower tool's cons
worn.
emission if the power tool is being used over longer period of
This field may under
Wear ear protection
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
ozzle.
to be thinned before they are suitable
GB
rec for different types of material.
Water based paint 20 - 25 seconds
Primers 24 - 28 seconds
Varnishes 20 - 25 seconds
Oil based paints 18 - 22 seconds
Enamel paints 18 - 22 seconds
Aluminum paints 22 - 25 seconds
Wood sealers 28 - 35 seconds
Wood preserva ves No thinning required
Wood stains No thinning required
Spraying
(Fig.3)
Fill the paint container (5) with the correctly thinned and strained paint. Connect the spray gun to the
mains supply. Aim the spray gun at a piece of scrap material and operate the trigger switch (3) un
is spraying. Adjust the output control (2) un
control (2) in a clockwise dir to reduce the flow and an
of the output control (2) will affect the spray pa ern.
Sp raying techniques (Fig.4) (Fig.5)
To obtain the best results, keep your spray gun level and parallel to the surface a
25 - 30 cm from the surface and spray evenly from side to side or up and down. Do not spray at an angle as
this will lead to paint runs on the surface. Use smooth and even strokes. When spraying large areas, using a
criss-cross pa ern as shown.
Never start or stop the spray gun while it is aimed at the surface to be sprayed. Evenly control the speed
of movement of the spray gun. A fast speed of movement over the surface will give a thin coat and a slow
speed will give a heavy coat. Apply one coat a
the manufacturers dr recommenda
keep the output control (2) on a low se
Where possible, avoid stopping and st
enough paint being applied.
Nozzle adjustment (Fig.7)
The spray pattern shape is adjusted by turning the ears of the air cap to either the vertical, horizontal, or
diagonal positions. The positions of the air cap and the corresponding spray pattern shapes are illustrated.
Test each pattern and use whichever pattern is suitable for your application.
NEVER trigger the gun while adjusting the ears on the air cap. NEVER point the spray gun at any
part of the body.

CLEANING AND MAINTENANCE

Always remember to disconnect from the mains supply before cleaning the spray gun or paint container. (5)
It is essen at the spray gun is cleaned and oiled thoroughly a er every use. Failure to clean and
oil it will almost certainly result in blockages and it may not operate when you next come to use it! The
guarantee does not cover cleaning a sprayer that has not been properly cleaned by the user.
The follo st be taken a er every use:
1. Empty any remaining material from the container.
2. Clean the container thoroughly with the thinner that was used.
3. Pour some thinner into the container and spray through the spray gun un
out of the nozzle.
4. Thoroughly clean the paint pick up pipe and filter with thinner.
5. Clean the basket and nozzle and remove any other debris or paint that remains.
6. Turn the spray gun upside down and apply a few drops of light oil to the two apertures
7. switch on the unit for a while, this will lubricate the piston and cylinder.
If your spray gun should require extra internal cleaning, it may be necessary to disassemble it.
If so the follo taken:
1. Turn both knobs on both sides of the Air Compressor Assembly to the "Unlock" position, and Insert the
spray gun into the Air Compressor Assembly into place,Turn both knobs on both sides of the Air Compressor
Assembly to the "Lock" position to lock the two pieces into place. (Fig.6)
(Fig.2)
required volume of paint is spraying. Turn the output
to increase the flow. Adjustment
Keep the nozzle
coat is required, make sure you observe
efore applying a second coat. When spraying small areas,
avoid using too much paint and prevent overspray.
raying an object. This can lead to too much, or not
GB
nt
coming
5