Installation - Bestway MY FIRST FRAME POOL Benutzerhandbuch

and should be self-closing and have a self-latching device. Gates
other than pedestrian access gates should have a self-latching device.
Where the release mechanism of the self-latching device is located
less than 54 inches from the bottom of the gate, (a) the release
mechanism should be located on the pool side of the gate at least 3
inches below the top of the gate and (b) the gate and barrier should
have no opening greater than 1/2 inch within18 inches of the release
mechanism.
9. Where a wall of a dwelling serves aspart of the barrier, one of the
following should apply:
(a) All doors with direct access to the pool through that wall should be
equipped with an alarm which produces an audible warning when
the door and its screen, if present, are opened. The alarm should
sound continuously for a minimum of 30 seconds within 7 seconds
after the door is opened. Alarms should meet the requirements of
UL2017 General-Purpose Signaling Devices and Systems, Section
77. The alarm should have a minimum sound pressure rating of 85
dBA at 10 feet and the sound of the alarm should be distinctive
from other household sounds, such as smoke alarms, telephones,
and door bells. The alarm should automatically reset under all
conditions. The alarm should be equipped with manual means,
such as touchpads or switches, to temporarily deactivate the alarm
for a single opening of the door from either direction. Such
deactivation should last for nomore than 15 seconds. The
deactivation touchpads or switches should be located at least 54
inches above the threshold of the door.
(b) The pool should be equipped with a power safety cover which
complies with ASTM F1346-91 listed below.
(c) Other means of protection, such as self-closing doors with
self-latching devices, are acceptable so long as the degree of
protection afforded is not less than the protection afforded by (a) or
(b) described above.
10. Where an aboveground pool structure is used as a barrier or where
the barrier is mounted on top of the pool structure, and the means of
access is a ladder or steps, then (a) the ladder to the pool or steps
should be capable of being secured, locked or removed to prevent
access, or (b) the ladder or steps should be surrounded by a barrier
which meets Section I, Paragraphs 1 through 9. When the ladder or
steps are secured, locked, or removed,any opening created should
not allow the passage of a 4-inch diameter sphere.
Section II: Barrier Locations
Barriers should be located so as to prohibit permanent structures, equipment
or similar objects from being used to climb the barriers.
Parts:
Liner
A
C
E
Structure photo:
B
A
B
Drawings may not reflect actual product, not scaled to size.
Underwater adhesive repair
patch
B
D
A
A
B
A
B
D
C
E
Ref# Description
A Top Rail A
B
Top Rail B
C Vertical Pool Leg
D Corner
E Footing
Preparation
Installation of small swimming pool usually takes only 10 minutes with 1 people
Recommendations regarding placement of the pool:
• It is essential the pool is set up on solid, level ground. If the pool is set
up on uneven ground it can cause collapse of the pool and flooding,
causing serious personal injury and/or damage to personal property.
Setting up on uneven ground will void the warranty and service claims.
• Do not set up on driveways, decks, platforms, gravel or asphalt. Ground
should be firm enough to withstand the pressure of the water; mud,
sand, soft / loose soil or tar are not suitable.
• The ground must be cleared of all objects and debris including stones and twigs.
• Check with your local city council for by-laws relating to fencing, barriers,
lighting and safety requirements and ensure you comply with all laws.

Installation

Assembly can be completed without tools.
NOTE: It is important to assemble pool in the order shown below. Adult
assembly required.
B A
Fig. 1
Fig. 3
1. Find solid, level ground and clear it of debris.
Attention: Do not set up the pool under cables or under trees.
2. Spread out the pool and make sure it is right side up.
3. Cover the water valve.
4. Assemble the top rails. Connect Top Rail A to Top Rail B, ensure the
spring-loaded pins snap into the pre-drilled holes, and slide into the
pole sleeve (Fig.1). Please see the structure photo for detailed
directions. Make sure the top rails' ends are in right position.
5. At the corners, insert the Top Rails (A & B) into the Corners (D). (Fig. 2)
6. Insert the Vertical Pool Legs (C) into the bottom of the Corners (D).(Fig. 3)
7. Attach all Footings (E) to the bottom of the Vertical Pool Legs (C). (Fig. 4)
8. Test the Frame to ensure all connections are secure before filling with water.
9. Put 1'' to 2'' (2 to 5cm) of water in the pool to the cover the floor. Once
pool floor is slightly covered, gently smooth out all wrinkles. Start in
the center of the pool and work your way clockwise to the outside.
10. Continue to fill the pool until reaches the water fill line located on the
pool's interior. Please kindly pay the utmost attention not over fill the
pool for security reasons.
Dismantling
1. Open water valve on the bottom of the pool, water will drain
automatically. (Check local regulations for drainage by-laws). Then
dismantle the frame of the pool to release the water. Make sure release
most of the water in 20 minutes.
Note: Drain by adult only!
2. Air dry pool.
ATTENTION: Do not leave the drained pool outside.
Repair
If your pool is damaged, use the provided repair patch.
1. Clean area to be repaired.
2. Carefully peel patch.
3. Press patch over area to be repaired.
4. Wait 30 minutes before inflation.
Pool Maintenance
Warning: If you do not adhere to the maintenance guidelines covered herein, your
health might be at risk, especially that of your children.
1. Change the water of pools frequently (particularly in hot weather) or
when noticeably contaminated, unclean water is harmful to the user's health.
2. Please contact your local retailer to obtain chemicals to treat the water
in your pool. Be sure to follow the chemical manufacturer's instructions.
3. Proper maintenance can maximize the life of your pool.
4. See packaging for water capacity.
Cleaning and Storage
1. After deflation, use a damp cloth to gently clean all surfaces.
Note: Never use solvents or other chemicals that may damage the product.
2. Remove all the accessories and spare parts of the pool and store them
clean and dry.
3. Once pool is completely dry, sprinkle with talcum powder to prevent
pool from sticking together, fold pool carefully. If pool is not completely
dry, mould may result and will damage the pool liner.
4. Store liner and accessories in a cool, dry place out of children's reach,
with a moderate temperature between 5°C / 41°F and 38°C / 100°F.
5. During the rainy season, pool and accessories should be stored as
instructed above.
6. Unproper draining of the pool might cause serious personal injury
and/or damage to personal property.
7. Check the product for damage at the beginning of each season and at
regular intervals when in use.
2
Pool Size & Quantity
1.22m x 1.22m x 30.5cm
(48'' x 48'' x 12'')
4
4
4
4
4
Fig. 2
Fig. 4
S-S-005093