jedo KODA Handbuch Seite 12

USER'S MANUAL
1. STROLLER UNFOLDING/FOLDING
- Release the safety lock of chassis before unfolding
(Photo no. 1).
- Unfolding of the stroller shall be enabled by pulling
the guide (handle) up while holding the chassis (Fig. 2).
When the guide is in the correct position, its blocking in
snap-in mechanism is made automatically, accompanied
by a clearly audible "click".
2. INSTALLING AND UNINSTALLING OF WHEELS
· Remove the plastic protectors from the axles ends of
the stroller. Protectors should be kept in order to secure
the axles when the stroller is not used.
To remove the rear wheels, press the button located in
the centre of the wheels (Photo no. 3) and remove the
wheels from the axles. To reinstall them, press the button
and slip the wheels on the axles, then release the button
and pull them towards yourself until they lock in.
- Install the10-inch front wheel (Photo no.4) with forks
by inserting the axle of the forks to turntable, until you
hear a "click" meaning that the wheel is locked at the
right position.
The front wheels can be locked for the straight-ahead
position by turning the upper part of the turntable
(Photo no. 5) clockwise until they click.
To remove the wheels, press the plastic button placed
on the top of turntable to the stop (Photo no. 5) and pull
the wheel with the forks to the bottom.
Warning! There is grease on the wheels which can stain
the fabrics.
· Risk of suffocation: one should ensure that the plastic
protectors of the ends of axles do not fall into the child's
hands.
3. STARTING OF BRAKES UP
· The stroller breaks by pressing the lateral brake pedal
(Photo no. 6), so that the ends of the brake lever block
the sprocket wheel.
· Releasing of the break is enabled by pulling the brake
pedal up.
4. ASSEMBLY / REMOVAL OF THE CARRY COT.
Assemble the carry cot on the chassis by inserting the
plastic carry cot adapters, located in its lower part, into
the central locking mechanism (Photo no. 7,8). Locking
will occur automatically. To remove the carry cot, press
buttons simultaneously on both sides of the carry cot
(Photo no.7), then lift the carry cot up.
WARNING! Before use, check if the carry cot is properly
locked in the central locking mechanism.
5. FOOTMUFF INSTALLATION
Put the footmuff on the carrycot and fasten it with the
snaps located on the sides of hood and footmuff.
6. SEAT ASSEMBLY (STROLLING INSERT)
The seat assembly and disassembly is performed similar
to the carry cot, with two buttons located on both sides
of the seat. The seat can be installed in two ways - facing
forward or rearward.
WARNING! Do not carry the seat by grasping the
footrest!
WARNING! Before use, check if the seat is properly
locked in the central latch.
WARNING! Before using the stroller, always check
whether the backrest is properly locked.
7. INSTALLATION / REMOVAL OF SEATS HOOD
The seat is equipped with its own hood, in order to
mount it on the seat, insert the plastic hood-fastening
elements located at the ends of the rod (Photo no.9) into
plastic connectors located on both sides of the backrest.
(Photo no. 10). To remove the hood, press the button on
the hood-fastening element, then pull the rod upwards.
8. INSTALLATION / REMOVAL /
RAIL HEIGHT ADJUSTMENT
Mount the safety rail by placing the element for rail
mounting in the connectors (Photo no. 11).
In order to remove the rail, press the gray button located
on both sides of the seat at the height of the rail (Photo
no.11 A), then pull it towards you. To change the height
of the rail, press the red button (Photo no. 11 B), located
on both ends, then set the desired height of the railing.
Locking in the selected position happens automatically.
9. ASSEMBLY OF FEET COVER (Seat)
Stretch cover on the seat and attach using press-studs.
10. STROLLER ASSEMBLING
- In order to put the chassis; remove the carrycot (point 4)
Next, fold the chassis by pressing the red button on the
right side of guide rail (Photo no. 12) and pulling up the
plastic handles for stroller folding located on the guide rail.
In order to further reduce the stroller size, the wheels can
be removed.
11. HANDLE HEIGHT ADJUSTMENT
Simultaneously press the two buttons on both sides of
the inside of the handle and move the handle to increase
or decrease its height accordingly. (Photo no. 13)
12. SETTING THE FOOTREST POSITION
The footrest can be adjusted in several positions. To
lower it, press the two buttons located on both sides of
the footrest and gently lower it down. (Photo no. 14). To
raise the footrest, lift it upwards, it will lock automatically.
13. ADJUSTING THE BACKREST OF THE SEAT.
The backrest of the seat can be set in several positions.
To lower the backrest, pull the plastic regulation element
located in the rear of the backrest, then set the correct
position. (Photo no.15)
To raise the backrest, simply push it upwards until you
reach the correct position. Locking will occur
automatically.
14. BACKREST ADJUSTING IN CARRYCOT
Backrest adjusting is performed by using the knob located
in the rear, lower, outer part of the carrycot. (Photo no. 16)