Herunterladen Inhalt Inhalt Diese Seite drucken

Automatic Operation (Auto Changeover) - Carrier 42NQ009 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 10
PRECAUTIONS FOR SAFETY
• Do not install, repair, open or remove the cover. It may expose you to
dangerous voltages. Ask the dealer or the specialist to do this.
• Turning off the power supply will not prevent potential electric shock.
• The appliance shall be installed in accordance with national wiring
DANGER
regulation.
• Means for disconnection from the supply having a contact separation
of at least 3 mm in all poles must be incorporated in the fi xed wiring.
• Do not expose your body directly to cool air for a long time.
• Do not insert your fi nger or any article into the air inlet/outlet.
• When an abnormality (burning smell, etc.) occurs, stop the air
WARNING
conditioner and disconnect the power supply or turn off the breaker.
• Do not wash the unit with water. It may cause an electric shock.
• Do not use this air conditioner for other purposes such as preserving
food, breeding animal, etc.
• Do not step or put anything on the indoor/outdoor unit. It may cause
an injury or damage the unit.
• Do not touch aluminium fi n because it may cause an injury.
• Before cleaning the unit, turn off the main switch or the circuit
CAUTION
breaker.
• When the unit won't be used for a long time, turn off the main switch
or the circuit breaker.
• It is recommended that maintenance be performed by a specialist
when the unit has been operated for a long time.
1
INDOOR UNIT DISPLAY
Models: 42NQ012, 42NQV012S
FILTER
PRE DEF
TIMER
OPERATION
RESET
Models: 42NQ009, 42NQV009S
CLEANING
RESET
TIMER
OPERATION
2
PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet)
Loading Batteries
1. Remove the cover. Insert 2 new
batteries (AAA type) following the
(+) and (–) positions.
2. Push RST : Reset the remote
control.
3. Place the cover back.
3
AIRFLOW DIRECTION
1
Press
FIX : Move the louver in
the desired vertical direction.
Press
SWING: Swing the air
2
automatically and press again
to stop.
For horizontal direction, adjust
3
manually.
Note:
• Do not move the louver manually by others.
• The louver may move automatically positioning by operation mode.
1 FILTER (Orange)
2 PRE DEF (DE-FROST) (Orange)
3 TIMER (Yellow)
4 OPERATION (Green)
5 RESET button
1 OPERATION (Green)
2 TIMER (Yellow)
3 RESET button
4
REMOTE CONTROL FUNCTION
1
Infrared signal emitter
2
Set louver button (FIX)
3
Auto louver button (SWING)
4
Mode select button (MODE)
5
Reset button (RST)
6
On timer button (ON)
7
Off timer button (OFF)
8
Reserve button (SET)
9
Cancel button (CLR)
!
Check button (CHK)
"
ECO button (ECO)
#
Fan speed button (FAN)
$
Start/Stop button (START/STOP)
%
Temperature button (
)
AUTOMATIC OPERATION (AUTO
5
CHANGEOVER)
To automatically select cooling or fan only operation and control fan speed.
1. Press MODE : Select AUTO.
2. Press
: Set the desired temperature.
The manufacture setting temperature is 24°C and available range of set
temperature is ±5°C.
6
COOLING / HEAT / AUTO FAN OPERATION
1. Press MODE: Select COOL, HEAT or AUTO FAN.
2. Press
: Set the desired temperature.
COOL: Min 17
o
C, HEAT: Max 30
o
C, AUTO FAN :
No temperature indication
3. Press
FAN : Select AUTO, LOW
7
DRY OPERATION
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press MODE : Select Dry.
2. Press
: Set the desired temperature.
8
ECONOMICAL OPERATION
To automatically control room temperature, fan speed and operation mode
1. Press ECO in the AUTO and COOL operation: Start and stop the
operation.
2. Press MODE or FAN after stopping the operation.
Note:
• Under certain conditions, ECO mode may not provide adequate cooling
due to energy saving features.
9
TEMPORARY OPERATION
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on
AUTOMATIC operation, preset
temperature is 24°C and fan
operation is automatic speed.
1
Hr.ON OFF
%
$
2
SWING
FIX
FAN
#
3
MODE
ECO
4
RST CHK
"
5
!
TIMER
6
9
ON
OFF
SET
CLR
7
8
, MED
, HIGH
.

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis