Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
handle (5) or the mechanical control (15) on
the handle of the flexible hose (14).
– After the unit operation, switch the vacuum
cleaner off by pressing the button (1) and
unplug the unit.
– To wind the cord, press the button (6), hold
the winding cord with hand in order to avoid
its whipping and damage.
– Between operations use the brush storage
space (2) (pic. 4).
– Use the handle (8) for carrying the vacuum
cleaner.
WARNING: Do not use the dust container
handle (11) for carrying the vacuum cleaner.
cleaning and care
Remove garbage and dust from the dust con-
tainer (9), disassemble and clean it after every
usage of the vacuum cleaner.
Start cleaning only after removing dust and gar-
bage from the dust container (9).
removing of the dust container (9) and re-
moval of dust and garbage from it
– Switch the unit off and unplug it.
– Remove the flexible hose (13) by turning the
flexible hose ending (12) counterclockwise.
– Push the dust container clamp (7) holding it
by the handle (8) and remove the dust con-
tainer (9) (pic. 5).
– Open the dust container flask lid (26) by
pressing the clamp (27) (pic. 6).
– Remove accumulated dust and garbage from
the dust container (9).
Disassembling and cleaning of the dust con-
tainer (9)
– Switch the unit off and unplug it, remove the
dust container (8), remove dust and garbage
from it.
– Holding the dust container handle (11) with
one hand, turn the carrying handle (8) clock-
wise relative to the flask (25) and remove the
flask (25).
– Set the outlet filter lid clamp (22) to the posi-
tion
(lift the clamp (22) upwards), holding
the separator (24), turn the carrying handle
(8) clockwise relative to the separator (24)
and remove the inlet filter (25) lid (21).
MW-3221.indd 10
– Remove the inlet filter (23) and clean it from
dust.
– Wash the separator (24), the inlet filter (23)
and the flask (25) under warm water jet.
Note: Dry all the parts thoroughly before as-
sembling the dust container.
– Install the inlet filter (23) back to its place,
match the mark on the upper part of the
separator (24) with the mark
filter lid (21), holding the separator, and turn
the lid (21) counterclockwise, holding by the
handle (8), till the marks
Fix the lid (21) by pressing the clamp (22).
– Insert the assembled separator into the flask
(25) and, holding by the handle (11), turn the
handle (8) counterclockwise till bumping.
– Install the dust container (9) back to its place
until the clamp (7) clicks.
cleaning the outlet filter (4)
Clean the outlet filter (4) regularly.
– Remove the outlet filter grid (3) by pressing
the clamp and pulling the grid (3) towards
yourself.
– Remove the outlet filter (4) from the inner
side of the grid (3), wash it under warm water
jet and then dry it thoroughly.
– Fix the outlet filter on the inner side of the
grid (3).
– Install the grid (3) back to its place.
The body of the vacuum cleaner
– Wipe the body of the vacuum cleaner with a
soft damp cloth.
– Do not immerse the body, the power cord
and the power plug of the unit into water
or other liquids. Provide that no water gets
inside the unit.
– Never use solvents or abrasives to clean the
surface of the vacuum cleaner.
– Do not wash the separator, the dust con-
tainer flask and filters in the dish washing
machine.
– Do not dry the inlet and outlet filters with a
hair dryer.
Storage
– Before taking the vacuum cleaner away for
storage clean its body, the dust container (9)
and the filters (4, 23).
10
on the inlet
and
match.
19.11.2013 10:36:56
Werbung
Inhaltsverzeichnis
