Stienen B.E. PFB-35 Kurzanleitung Seite 7

Total amount of feed fed so far (shown using both displays).
1212432 kg is shown as follows:
If you change the "0" to "1" all feed counter readings (including
the total amount) are deleted.
W /
ATER FEED RATIO
Today's current water/feed ratio is shown on the left-hand
display.
Yesterday's water/feed ratio is shown on the left-hand display.
T / S
IME TART A NEW FEED PERIOD
The time is used to increase the day number of the feed curve. Press the
The right-hand display shows the time; use the plus or minus key to change this value.
If you hold down the [ TIME ] key for 5 seconds or more,
interrupted. The feeding cycle is restarted afterwards.
FEED CURVE
You can use the feed curve to pre-program the amount of feed to be dosed on the basis of the animals' age
(provided that the PFB-35 feed weigher is NOT controlled by a control computer such as the PFM-9200 or
PL-9200, in which case you cannot set a feed curve on the PFB-35 feed weigher). You must push a sequence
of keys to set a curve. A curve consists of a maximum of 24 breakpoints.
Note! When the FEED CURVE is
active, you can only
change the feed dosage
by changing the feed
curve setting.
The breakpoint number which was set last is shown on the left-hand side of the left-
hand display (the "BREAKP." indicator is flashing). You can change the breakpoint
number using the plus and minus keys.
The day number for the relevant breakpoint is shown in the right-hand display (the
"BREAKP." indicator lights up continuously and the "DAY" indicator flashes). You can
change the day number using the plus and minus keys.
The left hand display shows the breakpoint number and the day number
corresponding with the breakpoint. The total kilos of feed to be dosed per day from
the day number set is shown on the right-hand display. You can change the dose
using the plus and minus keys.
[ TIME ]
the active feeding cycle is
6000
5000
4000
3000
2000
1000
0 7 14 21 28
Day number
S
WITCHING THE FEED CURVE ON
If you press the [ DAY ] key, the right-hand display will show the current day number of the
curve. If this is 0, the
can use the plus and minus keys to set the day number between 0 and 999 (0 = curve off).
ALARMS
S
WITCHING MAIN ALARM ON
Press the
alarm). In the right-hand display you can set that the alarm should be passed on to an external
device through the "ERROR" relay (1) or that it should not be passed on (0). If you have set "do
not pass on" (0) the "
relay after an alarm delay time set by the installer has elapsed (standard 5 seconds).
If the main alarm is off, the feed computer CANNOT pass on ANY MORE ALARMS to the user and/or the
connected equipment. This means that you should not switch off the main alarm too flippantly and that you
have to understand the consequences involved. This also applies to the other alarms.
S
key. WITCHING AN ALARM GROUP ON
Press the [ ALARM ]
'ALARM' indicator will turn off). Then switch on the alarm of the group again.
the group off, the group in question can no longer generate alarms if a fault situation occurs.
E.g. if you set "AL 2" to "0" (off), all alarm codes which begin with 2, such as alarm code 201, will be
switched off. The current alarm code is shown on the left-hand display.
L
ATEST ALARM
Alarm code
0 No alarm
1 Load cell alarm
2 Faulty weighing
hopper calibration
1x Module x not installed
35 42
2x Module x reset alarm
3x Configuration module
x changed
40 Feed sensor alarm
41 Feed sensor defect
50 Voltage discharge
hatch to low.
51 Discharge hatch
blocked
/
OFF
feed curve is off. If this is 1 or higher
/
OFF
[ ALARM ] key. The left-hand display now shows the current alarm code (0 = no
" indicator flashes. The alarm will only be passed on to the "ERROR"
/
OFF
key until the relevant alarm group is shown. Switch off the alarm of the group (the
The cause of the alarm that occurred the last is shown on the left-hand display. In the
right-hand display the time until which the alarm is/was active is shown.
Description
-
Load cell defective, overloaded or load cell connected incorrectly.
The difference between taring an "empty" weighing hopper and a "full"
weighing hopper (weighing hopper with reference weight) is too small (the
difference between parameters 4.05 and 4.07 must be at least 2000).
Carry out the calibration procedure again.
Module number x does not exist (x = module number)
The module x incessantly resets due to, for example, a fault, check the (x =
module number)
Module configuration x (number of outputs) is changed. Upload the module
number again ( x = module number)
Feed sensor not connected (both the FEED and NO FEED indicators are off).
Feed sensor not connected correctly (both the FEED and NO FEED
indicators are on).
Inspection cover has been opened
Fuse F2 630mA, slow-acting, on bottom PCB broken
Feed has caked
Something is stuck in the weighing hopper.
the feed curve is active. You
Note! If you leave the alarm of