Maintenance; Ec Declaration Of Conformity - Makita BO4553 Betriebsanleitung

To remove the sandpaper:
1. Set the tool upside down so that the sandpaper is on
top.
2. Grasping one corner of the sandpaper, peel it from
the pad.
Note:
If the sandpaper is in good condition, save it for further
use.
When sanding in narrow, hard-to-reach areas (e.g., shut-
ters, blinds, louvres), attach the cone-shaped abrasive
papers to the end of the pad (bottom and top). To sand
the end of thin materials, fold the abrasive paper and
attach to the side of the pad as shown in Fig. 4 and 5.
Dust bag (Fig. 7)
The use of the dust bag makes sanding operations clean
and dust collection easy. To attach the dust bag, fit the
bag's entry port onto the dust spout on the tool so that
the hole in the entry port is just over the protrusion on the
dust spout.
For the best results, empty the dust bag when it becomes
about half full, tapping it lightly to remove as much dust
as possible.
Installing paper dust bag
To install the paper dust bag, place the paper dust bag on
the paper dust bag holder with its front side upward.
Insert the front fixing cardboard of the paper dust bag
into the groove of the paper dust bag holder. (Fig. 8)
Then press the upper part of the front fixing cardboard in
arrow direction to hook it onto the claws. (Fig. 9)
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool. (Fig. 10 & 11)
Switch action (Fig. 12)
CAUTION:
Always check to see that the tool is switched off before
plugging in the tool.
To start the tool, press the "ON ( I )" side of the switch. To
stop, press the "OFF (O)" side of the switch.
Operation (Fig. 13 & 14)
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the work-
piece surface. A finishing sander is generally used to
remove only a small amount of material at a time. Since
the quality of the surface is more important than the
amount of stock removed do not bear down on the tool.
Keep the base flush with the workpiece at all times.
Excessive pressure may damage the paper and shorten
tool life.
You can put a high polish on furniture or other fine sur-
faces by using a cloth under the tool.
For BO4561 and BO4563
This tool is handy for sanding louvres, etc. When sanding
louvres, insert the protruding portion of the pad between
the louvres and sand them using the upper or lower side
of the abrasive paper.
CAUTION:
• Do not block motor vent with your finger or hand.
• Never run the tool without paper. You may seriously
damage the pad.

MAINTENANCE

CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by a
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.
Noise and Vibration of Model BO4553/BO4554
The typical A-weighted sound pressure level is 83 dB (A).
Uncertainty is 3 dB (A).
The noise level under working may exceed 85 dB (A).
– Wear ear protection. –
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.
Noise and Vibration of Model BO4561
The typical A-weighted sound pressure level is 80 dB (A).
Uncertainty is 3 dB (A).
The noise level under working may exceed 85 dB (A).
– Wear ear protection. –
The typical weighted root mean square acceleration
2
value is 8 m/s .
These values have been obtained according to
EN60745.
Noise and Vibration of Model BO4563
The typical A-weighted sound pressure level is 82 dB (A).
Uncertainty is 3 dB (A).
The noise level under working may exceed 85 dB (A).
– Wear ear protection. –
The typical weighted root mean square acceleration
2
value is 10 m/s .
These values have been obtained according to
EN60745.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents,
EN60745, EN55014, EN61000
in accordance with Council Directives, 89/336/EEC and
98/37/EC.
Yasuhiko Kanzaki
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
ENG003-2-V2
2
.
ENG004-2-V3
ENG004-2-V3
CE 2005
Director
ENH101-5
7