Makita LS1016L Bedienungsanleitung Seite 12

Tilt the saw blade until the pointer points to the desired
angle on the bevel scale. Then tighten the lever
clockwise firmly to secure the arm.
Fig.14
When the latch lever is pulled toward yourself, the saw
blade can be locked using positive stops at the right and
left 22.5 ° and 33.9 ° angle to the base surface.
When the latch lever is pushed forward as shown in the
figure, the saw blade can be locked at an desired angle
within the specified bevel angle range.
CAUTION:
When tilting the saw blade, be sure to raise the
•
handle fully.
After changing the bevel angle, always secure the
•
arm by tightening the lever clockwise.
When changing bevel angles, be sure to position
•
the kerf boards appropriately as explained in the
"Positioning kerf boards" section.
Slide lock adjustment
Fig.15
To lock the lower slide pole, pull the lock lever toward
yourself.
To lock the upper slide pole, turn the locking screw
clockwise.
Switch action
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and
returns to the "OFF" position when released.
Do not pull the switch trigger hard without pressing
•
in the lock-off button. This can cause switch
breakage.
For European countries
Fig.16
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push the lever to the left, press in the lock-off button and
then pull the switch trigger. Release the switch trigger to
stop.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
For all countries other than European countries
Fig.17
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
WARNING:
Do not use a lock with a shank or cable any
•
smaller than 6.35 mm in diameter.
NEVER use tool without a fully operative switch
•
trigger. Any tool with an inoperative switch is
HIGHLY DANGEROUS and must be repaired
before further usage.
For your safety, this tool is equipped with a lock-off
•
button which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off button. Return tool to a Makita service
center for proper repairs BEFORE further usage.
NEVER tape down or defeat purpose and function
•
of lock-off button.
Electronic function
Constant speed control
Possible to get fine finish, because the rotating
•
speed is kept constantly even under the loaded
condition.
Soft start feature
Soft start because of suppressed starting shock.
•
Laser beam action
For model LS1016L only
Fig.18
CAUTION:
Never look into the laser beam. Direct laser beam
•
may injure your eyes.
LASER RADIATION, DO NOT STARE INTO THE
•
BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS, CLASS 2M LASER PRODUCT.
To turn on the laser beam, press the upper position (I) of
the switch. Press the lower position (O) to turn off.
Laser line can be shifted to either the left or right side of
the saw blade by adjusting the adjusting screw as
follows.
Fig.19
1. Loosen the adjusting screw by turning it
counterclockwise.
2. With the adjusting screw loosened, slide the
adjusting screw to the right or left as far as it goes.
3. Tighten the adjusting screw firmly at the position
where it stops sliding.
Laser line is factory adjusted so that it is positioned
within 1 mm from the side surface of the blade (cutting
position).
NOTE:
When laser line is dim and almost or entirely
•
invisible because of the direct sunlight in the indoor
or outdoor window-by work, relocate the work area
to a place not exposed to the direct sunlight.
Aligning the laser line
Fig.20
Laser line can be shifted to either the left or right side of
the blade according to the applications of cutting. Refer
to explanation titled "Laser beam action" regarding its
shifting method.
12