Environmental Considerations; Fcc Compliance - illumina HiSeq 1500 Handbuch

HiSeq 1500 and HiSeq 2000 Systems Safety and Compliance Guide
Hot Surface Safety Warning
Do not operate the instrument with any of the panels
removed.
Do not touch the temperature station in the flow cell
compartment. The heater used in this area is normally
controlled between ambient room temperature (22°C)
and 95°C. Exposure to temperatures at the upper end of
this range can result in burns.
Heavy Object Safety Warning
The instrument is heavy and can cause serious injury if
dropped or mishandled.
Only personnel authorized byIlluminacan uncrate,
install, or move the instrument. Each time the instrument
is moved, install the shipping brackets to prevent stage
assembly damage. Significant risks to optical and
mechanical alignment can occur. The instrument must
be properly repositioned and recalibrated.
Uncrating, Installing, and Moving the Instrument
Only personnel authorized by Illumina can uncrate, install, or move the
instrument. If you have to relocate the instrument, contact your Illumina
representative.

Environmental Considerations

Element Specification
Temperature Maintain a lab temperature of 19°C to 25°C
(22°C ±3°C). This temperature is the operating
temperature of the instrument. During a run,
do not allow the ambient temperature to vary
more than ±2°C.
Humidity Maintain a noncondensing relative humidity
between 20–80%.
Elevation Locate the instrument at an altitude below
2000 meters (6500 feet).
Air Quality Operate the instrument in a Pollution
Degree II environment or better. A Pollution
Degree II environment is defined as an
environment that normally includes only
nonconductive pollutants.
Ventilation Consult your facilities department for
ventilation requirements based on the
instrument heat output specifications.
Product Certifications and Compliance
The HiSeq 1500 and HiSeq 2000 are certified to the following standards:
} UL STD 61010-1
}
CSA STD C22.2 No. 61010-1
} IEC/EN 61010-1
} IEC/EN 61326-1
The HiSeq 1500 and HiSeq 2000 comply with the following directives:
}
Low Voltage Directive 2006/95/EC
} EMC Voltage Directive 2004/108/EC
Compliance and Regulatory Markings
The instrument is labeled with the following compliance and regulatory
markings.
This label assures that the product is compliant with
safety standards and has been tested and certified by a
third-party organization.
This label assures that the product meets the essential
requirements of all relevant EU directives.
This label assures that the product complies with the
Environmental Protection Use Period - 10 years.
Restriction of Hazardous Substances (RoHS)
This label indicates that the instrument meets the WEEE
Directive for waste.
Return the instrument to Illumina for disposal.
Product Compliance and Regulatory Statements

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following 2 conditions:
1 This device may not cause harmful interference.
2 This device must accept any interference received, including interference
that may cause undesired operation.
CAUTION
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instrumentation
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case users will be required to correct the
interference at their own expense.
Shielded Cables
Shielded cables must be used with this unit to ensure compliance with the
Class A FCC limits.
Document # 1000000000665