Specifications - Fender Passport PD-150 Bedienungsanleitung

3. Consider the application and needs of the
event and set the System EQ control as
appropriate. This is best achieved by playing
recorded material of the same type as your
show program, or by having an assistant
speak into the microphone while you listen in
the audience area.
For public address (spoken voice), it is
advisable to rotate the System EQ control
clockwise to enhance the mid and high
frequencies, and limit the low frequency
content. For large outdoor spaces this will also
give the maximum headroom and output
capability. Carefully consider the individual
event's needs and set your control for the
maximum effect.
POWER TOWER ™
In setting up the system, the Passport Mixing
console should ideally be placed where
system performance can be evaluated by the
operator. If no ongoing adjustments will be
necessary, the mixer may be placed
conveniently and where the cable lengths
allow.
Take care to place the Power Tower where the
cables will not trip anyone. All cables should
be carefully secured.
The storage compartment in the rear of the
Tower can hold cables, microphones and
other system parts. To open simply slide the
catch upwards and pull open.
The mains (AC) fuse holder is under the IEC
(power cord) socket on the right rear of the
Tower. To change a fuse, remove the IEC plug
and, using an appropriate tool pull out the fuse
holder. Note there is a spare fuse in the fuse
holder; the Passport utilizes a T4A, 250V fuse.
Only replace fuses with one of an identical
value and size.
The Passport System is weather resistant in its
packed transport mode. However, when
operating outdoors, take care to fully protect
the Power Tower in the event of exposure to
rain. Remember to allow free air flow
through the front air inlet located at the
bottom of the front panel on the Passport
power tower.

SPECIFICATIONS

Part Number
069-2005-0X3
Frequency Response
20 Hz to 40 kHz ± 1 dB (at send output)
30 Hz to 30 kHz ± 1 dB (at speaker output,
with processor threshold exceeded)
Distortion
< 0.1%, 20 Hz to 20 kHz, 1 dB below rated output
System Signal to Noise Ratio
> 80 dB @ 1 w, "A" WTD
Power Output
75W/ch continuous average power, 8ohm,
both channels driven with THD < 1 %
Input Impedance (Channels 1-2-3 XLR and 1/4")
"Mic" switch position: 2 k ohm
"Line" switch position: 66 k ohm
Input Impedance (Phono and Stereo Channel 1/4")
78 k ohm
Max. Input Level
Mic:
Line:
Stereo: 26 dBu
Return Input Impedance
47k ohm
Fuse type
T4A, 250V
Passport System
Width: 610 mm (24 in.)
Height: 541 mm (18 in.)
Depth: 254 mm (10 in.)
Weight: 11.83 kgs (26 lbs)
Speakers
Width: 245 mm (9.65 in.)
Height: 439 mm (17.5 in.)
Depth: 241 mm (9.5 in.)
Weight: 3.3 kgs (7.25 lbs)
Power Tower
Width
Height 451 mm (18 in.)
Depth
Weight 5.23 kgs (11.5 lbs)
Tower Footprint
241 x 298 mm (9.5 x 11.75 in.)
Microphone
Dynamic Cardioid, balanced
Microphone Cable
XL -Male to XL-Female, 6 m (20 feet)
Speaker Cables
1/4 in. to 1/4 in., 9 m (30 feet)
0 dBu is referenced to 0.775 volts rms
7
-7 dBu
30 dBu
254 mm (10 in.)
178 mm (7 in.)