Inhaltsverzeichnis
Werbung
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR ROUTERS
GENERAL
• This tool should not be used by people under the age of
16 years
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
• SKIL can assure fl awless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• Do not use damaged or deformed router bits
• Only use sharp router bits
• Protect accessories from impact, shock and grease
• Only use high speed steel (HSS) or carbide-tipped (CT)
router bits with this tool
BEFORE USE
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to
a 220V supply)
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Clamp the workpiece in case it does not remain
stationary from its own weight
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with
a capacity of 16 Amps (U.K. 13 Amps)
• The noise level when working can exceed 85 dB(A);
wear ear protection
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause
allergic reactions and/or respiratory diseases to the
operator or bystanders); wear a dust mask and work
with a dust extraction device when connectable
• Certain kinds of dust are classifi ed as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Be sure tool is switched off when plugging in
DURING USE
• Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
• Never use the tool when cord or base-plate N 2
(=protective guard) is damaged; have it replaced by a
qualifi ed person
• Keep hands and fi ngers away from router bit when tool
is switched on
• Never exceed maximum cutting depth of router bit
(= B &) while cutting
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• In case the router bit is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
• In case of current interruption or when the plug is
accidentally pulled out, immediately switch off the tool
in order to prevent uncontrolled restarting
• Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
• After fi nishing the work, lift lever D 2, guide the tool
back into the upper starting position, and switch off the
tool
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
• Mounting/removing router bits 4
! switch off the tool and disconnect the plug
! ensure that router bit shaft is perfectly clean
10
Werbung
Inhaltsverzeichnis
