Specifications; Delivery Content - Zipper Maschinen ZI-HS8PT Handbuch

EN
2

SPECIFICATIONS

This log splitter is designed for operating under am-
bient temperatures between +5
installation at altitudes no more than 1000m above
M.S.L.
The surrounding humidity should be less than 50%
at 40 C.
o
It can be stored or transported under ambient tem-
peratures between -25
Motor
Log diameter range
Max. log length
Maximum Force
Hydraulic Pressure
Ram Travel
Forward Speed
Retract Speed
Noise Level
Length
Width
height
Weight
3
ElECTRIC REqUIREmENTS
With 3 phase 400 Volt / 50Hz motor, the log splitter
should be connected to standard 400V+10%
/ 50Hz+1Hz. Electrical supply which has protec-
tion devices of under-voltage, over-voltage, over-
current as well as a residual current device (RCD)
which maximum residual current rated at 0.03A.
The mains connection and extension cable must
have 5 wires = 3P + N + PE (3/N/PE).
The mains connection must have maximum 16 A
fuse. Electrical connection rubber cables must com-
ply with EN60245 which are always marked with
symbol H 07 RN. Cables should be identified, as it
is a legal requirement.
4
UNPACKING
Please see for reference Picture strip A. At least 2
people are required to unpack the log splitter pa-
ckage. Take the following steps to put the Log Split-
ter on the ground by tipping every side of the carton
by 45 degree. Stellen Sie ein solides Objekt (B) zu
einer Wand, lehnen Sie die Holzspalterverpackung
(A) an (B) an, schieben Sie auf der anderen Seite
C and 40 C and for
o o
C and 55 C.
o o
400V/50Hz 3500W S6/ IP54
12 cm ~ 32 cm
125 cm / 85 cm / 55 cm
8 t
20.4 Mpa
480 mm
5.4 cm/sec
19.2 cm/sec
80.1 dbA no load / 92.5 dbA full load
83 cm
93 cm
147 cm
148 kg
ZI-HS8PT
einen Keil (C) unter, um die Verpackung gegen Weg-
rutschen zu sichern! Öffnen Sie den Karton, lassen
Sie den Spalter vorsichtig herausrutschen, bis er
am Boden mit einer Kante ansteht
5

DElIVERY CONTENT

For reference, check picture B
1. Log Splitter Frame
2. Control Lever and Guard Assy
3. Wheel
4. Wheel Shaft
5. Owner's Manual
6. Hardware Bag, including
6
SET UP AND PREPARATION FOR OPERATION
WHEEL ASSEMBLY
1. For Reference see picture D
Fix the wheel shaft on the frame with four M8X20
screws, spring washers and flat washers as shown.
For Reference see picture E
2.
Put 3 Ø8 into the wheel shaft, then a wheel followed
by another flat washer. Insert a split pin into the
shaft holes outside each flat washer, then place the
wheel cover.
CONTROL LEVER AND GUARD ASSEMBLY
For Reference see picture G
3.
Pull Spring Pin (A) to remove the Lock Pin (B). Apply
a thin coat of grease to both surfaces of the Con-
trol Lever Guard as illustrated. Insert the Control
Lever and Guard Assy and make sure the Control
Lever End goes into the slot of Connection Bracket
(C). Lock the Control Lever and Guard Assy down
with the Lock Pin (B) and Spring Pin (A). Follow the
same steps to install the other Control Lever and
Guard Assy on the other side. Grease the Splitting
ram as well!
SUPPORT TABLE
4. For Reference see picture H
3 installation positions available for the Support Ta-
ble for different splitting length. At every installa-
tion positions, lock-down hooks (D) are available.
Insert the Support Table in the selected Brackets
(E). Turn the Lock Down Hooks (D) on both side by
90 degrees to lock the Support Table down.
1 set
2 sets
2 pairs
2 pairs
1 pc
1 set