Recycling Und Entsorgung - Blaupunkt GTb 1000 BP11 Bedienungsanleitung

Recycling und Entsorgung

Bitte nutzen Sie zur Entsorgung des Produktes die
zur Verfügung stehenden Rückgabe- und Sammel-
systeme.
Änderungen vorbehalten.
ENGLISH
Warranty
We provide a manufacturer's warranty for products bought
within the European Union. For devices purchased outside
the European Union, the warranty terms issued by our re-
spective responsible domestic agency are valid. The warranty
terms can be called up from www.blaupunkt.com.
Recommendation
The performance of an amplifi er can only be as good as its in-
stallation. A correct installation increases the overall perform-
ance of your car sound system. The GTA amplifi er should be
installed by a trained person. If you would to install it yourself,
please read these installation instructions very carefully and
allow yourself suffi cient time for the installation.
In conclusion, allow us a few words about the topic of health
protection:
During the playback of music in your vehicle, please consider
that continuous sound-pressure levels above 100 dB can
lead to permanent damages to the human ear and even to
loss of hearing. Using today's high-performance systems
and loudspeaker confi gurations allows for reaching sound-
pressure levels above 130 dB.
Safety notes
Please observe the following safety notes during the instal-
lation and connection.
– Disconnect the negative pole of the battery! Observe the
safety notes of the vehicle manufacturer.
– When you drill holes, ensure that you do not damage any
vehicle components.
– The cross section of the plus and minus cable may not
be less than 6 mm 2 .
– Use cable glands for holes with sharp edges.
– An incorrect installation can result in malfunctions of the
electronic vehicle systems or your car sound system.
Installation and connection instructions
With respect to accident safety, the GTA 250 BP11 must be
secured in a professional way.
When selecting the installation location, select a dry loca-
tion that offers sufficient air circulation for cooling the
amplifi er.
The GTA 250 BP11 must not be installed on rear shelves, rear
seats or other locations that are open to the front.
The installation location must be suitable to accept the ac-
companying screws and provide a fi rm support.
The amplifi er power cable must be fi tted with a fuse no more
than 30 cm from the battery to protect the vehicle battery in
case of a short circuit between power amplifi er and battery.
The fuse of the amplifi er protects only the amplifi er, not the
vehicle battery.
Use loudspeakers with 2 - 4 Ω impedance (see table or in-
stallation drawing). Observe the maximum power handling
capacity (music output). Do not connect loudspeakers to
earth, use only the referenced terminals.
Application options and loudspeaker connection
Stereo Mode
Max power
Mono mode
Max power
Stereo Mode
Max power
Stereo Mode
RMS power
Mono mode
RMS power
Stereo Mode
RMS power
Frequency response
Signal-to-noise ratio
Signal-to-noise ratio
Distortion factor (RMS)
Stability
Input sensitivity
Low-pass fi lter
(Low Pass)
High-pass fi lter
(High Pass)
Bass boost
Dimensions
W x H x D (mm)
W x H x D (")
Audio inputs (see Fig. 3)
You can select between 2 diff erent audio inputs;
– Cinch (RCA)
– Hi level (loudspeaker connections)
Use only one of the audio inputs; otherwise, it may lead to
audio interferences.
The preamplifi er outputs are connected to the cinch (RCA)
1
sockets via a shielded sound cable.
With control via the loudspeaker outputs, the input connec-
2 3
tions of pos. / are fed to the closest loudspeaker cables
(front or rear) on the left and right. They are separated and
connected to the input connections. The polarity of the + or -
connections must be observed. Bridge output stages (BTL) can
also be connected directly without an additional adapter.
GTA 250 BP11
2 x 110 W / 4 Ω Fig. 4, 5
1 x 330 W / 4 Ω Fig. 6
2 x 160 W / 2 Ω Fig. 4, 5
2 x 55 W / 4 Ω Fig. 4, 5
1 x 165 W / 4 Ω Fig. 6
2 x 80 W / 2 Ω Fig. 4, 5
10 Hz - 30,000 Hz
> 85 dB @ RMS power
> 75 dB @ 1 W / 1 kHz
< 0.05 %
2 Ω (4 Ω in bridge mode)
0.2 - 5 V
50 - 250 Hz
80 Hz
0 dB / 6 dB / 12 dB
197 x 52 x 187
7.8 x 2.1 x 7.4
5