Maintenance; Troubleshooting - THOMSON ROC1117PHI Bedienungsanleitung

6.4 CLEARING OF LEARNED KEYS
6.4.1 CLEARING OF ONE LEARNED KEY
1. Press and hold [MUTE] and [VOL+] keys
for 5 seconds until the LED will be lit.
2. Enter the code [9] [8] [1], the LED will
flash 2 times and then remain on.
3. Press and release the desired key at the
replacement remote control which you
want to clear the learned command. If the
LED flashes 3 times, the learned command
has been cleared successfully.
6.4.2 CLEARING OF ALL LEARNED KEYS
1. Press and hold [MUTE] and [VOL+] keys for
5 seconds until the LED will be lit.
2. Enter the code [9] [8] [2], the LED will flash
2 times and then remain on.
3. Press and release the [OK] key at the
replacement remote control. If the LED
flashes 3 times, all commands have been
cleared successfully.
7. SIMPLE Mode
This remote control is equipped with an
SIMPLE Mode. Thus you could reduce the
functionality of the remote control to its basic
functions. It avoids that the TV Settings are
changed by mistake.
During the SIMPLE Mode you still could use
following keys:
Switch the TV On or Off
– / + Change the volume
Mute the TV
Change the program
CH– / CH +
0-9 Numeric keys for program selection/
direct page selection Teletext
TEXT Teletext ON/OFF
Use to select a variety of on-screen
options
GUIDE Show the Electronic Program Guide
(if supported by the TV)
Select signal source
Exit Menu
TV Shift to TV
7.1 Enter SIMPLE Mode
1. Press and hold [MUTE] and [VOL+] keys for
5 seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash
two times and then remain on.
3. Press and release the [OK] key, if LED flash
3 times, you have entered the SIMPLE
Mode successfully.
5
5
5
7.2 Exit SIMPLE Mode
1. Press and hold [MUTE] and [VOL+]
for 5 seconds until the LED will be lit.
2. Enter the code [9] [7] [0], the LED will flash
two times and then remain on.
3. Press and release the [EXIT] key, if LED
flash 3 times, you have exit the SIMPLE
Mode.
Note
While the SIMPLE Mode is activated only
the keys mentioned in chapter 7 will work.
If one of these keys is pressed the LED will
be lit until the key is released. If one key is
pressed during the normal mode, the LED
will flash.

8. Maintenance

• Do not mix new and used batteries for
powering the Universal Remote Control, as
old batteries tend to leak and may cause
power drain.
• Do not use corrosive or abrasive cleansers on
your Universal Remote Control.
• Keep the Universal Remote Control dust free
by wiping it with a soft, dry cloth.

9. Troubleshooting

Q. My Universal Remote Control does not
work at all!
A. Check your TV. If the TV main switch is
turned off, your Remote cannot operate
your TV.
A. Check whether your batteries are inserted
properly and are in the correct +/- position.
A. Check whether you have pressed the
corresponding device mode key for your
device.
A. If the batteries are low, replace the
batteries.
Q. My TV responds only to some of the
commands.
A. Try other codes until most keys work
properly.
Q. Some keys of the Remote Control do not
work anymore?
A. Maybe the SIMPLE Mode had been
activated. Deactivate the SIMPLE Mode as
explained in chapter 7.2.
10. Warranty Disclaimer
The manufacturer assumes no liability and
provides no warranty for damage resulting
from improper installation/mounting, improper
use of the product or from failure to observe
the operating instructions and/or safety notes.
11. Service and Support
Please contact Hama Product Consulting if you
have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here:
www.hama.com
4
5