Technical Data; Angle Grinder; Declaration Of Conformity - Bosch GWS Professional 22-180 H Originalbetriebsanleitung

OBJ_BUCH-777-008.book Page 19 Wednesday, February 8, 2012 8:04 AM
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.

Technical Data

Angle Grinder

Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-Procedure 01/2003
Protection class
Angle Grinder
Article number
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Only for power tools without reduced starting current: Starting cycles generate brief voltage drops. Interference with other equipment/machines may
occur in case of unfavourable mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
GWS ... 22-180
H
3 601 ... H81 L..
W 2200
W 1500
-1
min 8500
mm 180
M 14
mm 25
–
–
kg 5.0
/II
GWS ... 24-180 24-230
JH H
3 601 ... H83 M.. H84 L..
W 2400 2400
W 1600 1600
-1
min 8500 6500
mm 180 230
M 14 M 14
mm 25 25
–
–
kg 5.0 5.1
/II /II
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
30.01.2012
English | 19
22-180 22-230 22-230
JH H JH
H81 M.. H82 L.. H82 M..
2200 2200 2200
1500 1500 1500
8500 6500 6500
180 230 230
M 14 M 14 M 14
25 25 25
–
–
5.0 5.2 5.2
/II /II /II
24-230 26-180 26-230
JH JH JH
H84 M.. H55 M.. H56 M..
2400 2600 2600
1600 1700 1700
6500 8500 6500
230 180 230
M 14 M 14 M 14
25 25 25
5.2 5.9 6.0
/II /II /II
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
1 609 929 X88 | (8.2.12)