Bedienung; Menüstruktur Kennen Lernen; 5Bbedienung - Rittal DK 7320.100 Montage-, Installations- Und Bedienungsanleitung

DE
6

Bedienung

6.1 Menüstruktur kennen lernen
Die Menüstruktur des Terminalprogramms ist wie
folgt aufgebaut:
1 Network Configuration
1.1 IP Configuration
1.1.1 IP Address
1.1.2 IP Subnet mask
1.1.3 IP Def. Gateway
1.1.4 Enable/Disable DHCP
1.1.5 Settings Ethernet Port
1.2 SNMP Configuration
1.2.1 Trap Receiver Confi-
guration
1.2.1.1 IP Trap Receiver
1.2.1.2 Enable/Disable
1.2.1.3 IP Trap Receiver
1.2.1.4 Enable/Disable
1.2.1.5 IP Trap Receiver
1.2.1.6 Enable/Disable
1.2.1.7 IP Trap Receiver
1.2.1.8 Enable/Disable
1.2.2 SNMPv1 IP Access
1.2.2.1 SNMPv1 Manager
1.2.2.2 SNMPv1 Manager
1.2.2.3 SNMPv1 Manager
1.2.2.4 SNMPv1 Manager
1.2.2.5 SNMPv1 Manager
1.2.2.6 SNMPv1 Manager
1.2.2.7 SNMPv1 Manager
1.2.2.8 SNMPv1 Manager
1.2.2.9 SNMPv1 Manager
1.2.2.A SNMPv1 Manager
1.2.2.B SNMPv1 Manager
1.2.2.C SNMPv1 Manager
1.2.3 Read Community
1.2.4 Write Community
1.2.5 Enable Auth. Traps
1.2.6 Change SNMP Versi-
on
1.2.7 Default SNMPv3 User
Name
CMC-TC Processing Unit II
1.4.2 IP Addr. CMC
(DialIn)
1.4.3 IP Addr. Client
(DialIn)
1.4.4 Username (DialIn)
1.4.5 Password (DialIn)
1.4.6 Callback Nr (DialIn)
1.4.7 Enable PPP (Dialout)
1.4.8 IP Addr. CMC
(Dialout)
1.4.9 IP Addr. Client
(Dialout)
1.4.A Username (Dialout)
1.4.B Password (Dialout)
1.4.C Phone Number
(Dialout)
1.4.D Modem type
1.4.E MSN (for ISDN)
1.4.F Modem Baudrate
1.5 SMTP (email) Configu-
ration
1.5.1 IP Addr. SMTP Ser-
ver
1.5.2 SMTP Server Au-
thentication
1.5.3 Username SMTP
Server
1.5.4 Password SMTP
Server
1.5.5 eMail Sender Name
1.5.6 eMail Reply to
1.5.7 eMail upon Unit
Messages
1.5.8 eMail Address
1.5.8.1 eMail Address
1.5.8.2 eMail Address
1.5.8.3 eMail Address
1.5.8.4 eMail Address
1.6 Syslog Konfiguration
1.6.1 IP Addr. Syslog
Server
1.6.2 IP Addr. Syslog
Server
1.6.3 Syslog Facility
1.6.4 Enable Syslog
1.7 System Name
1.8 System Contact

6 5BBedienung

1 Network Configuration
1.2.8 Default SNMPv3
Password
1.2.9 Confirm SNMPv3 us-
mUser/Passw
1.3 NTP Configuration
1.3.1 Enable NTP
1.3.2 IP Addr. NTP Server 1 1.A.2 Change Password
1.3.3 IP Addr. NTP Server 2 1.A.3 Change HTTP Port
1.3.4 NTP Offset to UTC
1.3.5 NTP Update Frequen-
cy (h)
1.3.6 Dayl. Saving Time,
Begin
1.3.7 Dayl. Saving Time,
End
1.4 PPP Configuration
1.4.1 Enable PPP (DialIn)
2 Sensor Units
2.1 z. B. IO Unit 1:'CMC-
TCIOU'
2.1.1 z. B. Temperature
Sensor
2.1.1.1 Status
2.1.1.2 Value
2.1.1.3 Setpoint High
2.1.1.4 Setpoint Warning
2.1.1.5 Setpoint Low
2.1.1.6 Message Text
2.1.1.7 Alarm Relay
2.1.1.8 Beeper
2.1.1.9 Trap Receiver 1
2.1.1.A Trap Receiver 2
2.1.1.B Trap Receiver 3
3 General Configuration
3.1 Temperature Unit
3.2 Beeper
3.3 Quit Alarm Relay
3.4 Alarm Relay Options
3.5 Web Access
3.6 Actual Date
3.7 Actual Time
3.8 Check Link
3.9 SMS Configuration
1.9 System Location
1.A Security
1.A.1 Change Password
User ´cmc´
User ´admin´
1.A.4 Enable SSL
1.A.5 Change HTTPs Port
1.B Enable FTP
1.C Cons./Teln. Timeout
Minutes
1.D Enable/Disable Telnet
1.E Activate Actual Values
2.1.1.C Trap Receiver
4/Log
2.1.1.D Alarm Reset
2.1.1.E Send SMS
2.1.1.F Send eMail
2.1.2 z. B. Humidity Sensor
2.1.3 not available
2.1.4 not available
2.1.5 Name Sensor Unit
2.1.4 Status of Unit
2.2 Unit 2 not available
2.3 Unit 3 not available
2.4 Unit 4 not available
3.9.2 SMS Service Number
3.9.3 ISDN MSN
3.9.4 ISDN Pre-Dial Num-
ber
3.9.5 ISDN Command
3.9.6 SMS upon Unit Mes-
sage
3.9.7 SMS Phone Numbers
3.9.7.1 SMS Phone Num-
ber
3.9.7.2 SMS Phone Num-
ber
3.9.7.3 SMS Phone Num-
ber
13