Femi 360 MULTY Gebrauchsanleitungen Seite 20

!$Ã @G@8USD86GÃ8PII@8UDPIÃ
Before connecting up to the power supply, make sure
that the mains voltage
specifications give in paragraph 1.2 "Technical
Features" as well as on the label (18) attached to the
side of the bench.
Also make sure that the mains network to which the
workbench is to be connected is earthed in accordance
with current safety standards and that the socket is in
good condition.
Avtà (Ã
ÃX6SIDIB)à Uurà ˆ†r…à v†Ã …r€vqrqà ‡uh‡Ã
ˆƒ†‡…rh€Ã s…‚€Ã ‡urà ƒ‚r…ƈƒƒy’Ár‡‚…xÃhÃ
€htr‡‚‡ur…€hyÃ
v†‡hyyrqà ‡‚à †hsrtˆh…qà hyyà ‡urà p‚qˆp‡‚…†Ã
s…‚€Ã†u‚…‡Ãpv…pˆv‡†Ãhq‰r…y‚hq†Ã
à Uuv†Ã ƒ…‚‡rp‡v‚Ã €ˆ†‡Ã irà pu‚†rÃ qrƒrqvtÃ
‚Ã ‡urà ryrp‡…vphyà puh…hp‡r…v†‡vp†Ã ‚sà ‡urÃ
irpuà h†Ã vqvph‡rqà ‚Ã ‡urà …ryh‡v‰rÃ
vs‚…€h‡v‚Ãƒyh‡rÃhssv‘rqÇ‚ÇurÃirpuÃv‡†rysÃ
Attach the tool's power connector (19) to one of the
sockets (20) located on the multifunction bench.
Then connect the bench's power cable to the mains
socket in order to enable functioning of the tool.
AvtÃ!Ã
Ã
Ã
Ã
Ã
Ã
16
corresponds to the
ƒ…‚‡rp‡v‚Ã €ˆ†‡Ã irÃ
!%Ã 69EVTUDIBÃUC@ÃXPSFDIBÃQPTDUDPIÃ
It is possible to adjust the work-piece support system
in various positions,
requirements and the work-piece being processed.
• The support system (9) can be set in two ways:
A. As a support for sliding a work-piece;
B. As a work-piece holding system.
AvtÃ! Ã
• Figures 22 and 23 illustrate the two different
functions of the support system (9).
AvtÃ!!Ã
Ã
AvtÃ!"Ã
à I PU@)à Avtˆ…rà !!à vÃ ƒh…‡vpˆyh…à vyyˆ†‡…h‡r†Ã
‡urÃp‚svtˆ…h‡v‚Ã‚sÇurÃirpuÐuvpuÃhyy‚†Ã
‡urȆr…Ç‚Ãph……’ˆ‡Ã‚…xÇurȃƒr…ÆvqrÃ
‚sÇurÃpˆ‡‡vtÇ‚‚yÃ
Ã
Follows ...
depending on working