Operating Elements And Connections; Safety Notes - Monacor TVSET-400 Bedienungsanleitung

Please unfold page 3. Then you can always see the
operating elements and connections described.
Contents
1

Operating Elements and Connections . . . . . 7

1.1 Switch-over unit . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2

Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Mounting and Setting-up . . . . . . . . . . . . . . . . 8
5 Connection of the Units . . . . . . . . . . . . . . . . . 8
5.1 Monitor or video recorder . . . . . . . . . . . . . . . . . 8
5.2 Connection of the cameras . . . . . . . . . . . . . . . . 8
5.3 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.4 Power supply of the infrared remote control . . . 8
6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6.1 Manual camera selection . . . . . . . . . . . . . . . . . 9
6.2 Operating mode AUTO . . . . . . . . . . . . . . . . . . . 9
6.3 Operating mode SCAN . . . . . . . . . . . . . . . . . . . 9
6.4 Adjustment of the dwell time . . . . . . . . . . . . . . . 9
7 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 9
1 Operating Elements and Connections
1.1 Switch-over unit (figs. 1 and 2)
1 Display for the channel number and to confirm the
input
2 Audio/video output jack OUTPUT to connect a
monitor or video recorder; an adapter cable with
phono plugs is supplied together with the set
3 Audio/video input jacks CH1 – CH4 to connect up
to 4 cameras of type TVCCD-520
4 Jack DC IN 12V to connect the supplied power
supply unit
5 POWER switch
1.2 Remote control (fig. 3)
6 Numerical keys to enter the picture sequence or
dwell time
7 SCAN button for automatic sequential switching of
the cameras in a defined order
8 AUTO button for automatic sequential switching of
the pictures of all connected cameras
9 DWELL button to adjust the dwell time in case of
automatic sequential switching of pictures
10 PRGM button to start the programming procedure
of picture sequence or dwell time and for final con-
firmation
11 Buttons CH1 – CH4 for manual selection of an
input channel
The buttons not mentioned are without function for this
system.
1.3 Camera (fig. 4)
12 Bracket for wall mounting
13 Infrared light diodes to illuminate the object to be
monitored
14 Lens with fixed focal length
2 Safety Notes
The units (switch-over unit, camera, and power supply
unit) correspond to the directive 89/336/EEC for elec-
tromagnetic compatibility. In addition, the power sup-
ply unit corresponds to the low voltage directive
73/23/EEC.
The power supply unit uses dangerous mains volt-
age (230 V~). To prevent a shock hazard, do not
open this unit! Leave servicing to authorized, skilled
personnel only. Besides, any guarantee claim ex-
pires if switch-over unit, power supply unit, or
camera has been opened.
It is essential to observe the following items:
Protect the units against heat and excessive cold
(admissible ambient temperature range 0 – 40 °C).
The switch-over unit and the power supply unit are
only suitable for indoor use. Protect them against
humidity.
The heat being generated in the switch-over unit has
to be carried off via air circulation. Therefore, the cir-
culation vents at the housing must not be covered
with any objects. Do not insert or drop anything into
the circulation vents! The unit may be damaged.
The camera housing is splashproof but not ab-
solutely watertight. Therefore, do not immerse the
camera in water.
Do not set the switch-over unit into operation, and
immediately disconnect the power supply unit from
the mains if:
1. damage at the switch-over unit, the camera, or
the power supply unit can be seen,
2. a defect might have occurred after a drop or simi-
lar accident,
3.there are malfunctions.
The units must in any case be repaired by author-
ized personnel.
For cleaning of the switch-over unit and the power
supply unit only use a dry, soft cloth, by no means
chemicals or water. Do not clean the camera
housing with strong detergents or chemicals.
If the units are used for purposes other than orig-
inally intended, if they are not connected or operated
correctly or not repaired in an expert way, there is no
liability for possible damage.
If the units are to be put out of operation definitively,
take them to a local recycling plant for disposal.
GB
7