Inhaltsverzeichnis
Werbung
(2) How to drill
To use for drilling lum ber
✶
Apply the point of the drill bit to the desired drilling
✁
p o si t i o n , h o l d t h e d r i l l p er p en d i cu l ar t o t h e
w orkpiece surface and turn on the sw itch.
When drilling a through hole in lumber, remove the
✁
drill from the material as soon as the tip of the drill
bit protrudes from the opposite surface. Then, turn
the workpiece over and complete the drilling from
the opposite side to obtain a clean hole. (Fig. 4)
If extra lum ber is applied under the lum ber you
w ant to drill and it is drilled together, a fine hole
w ill also be m ade. (Fig. 5)
A w ood-w orking drill need not be pressed strongly
✁
since it penetrates using the screw at the point.
Even if excessive force is used, a hole w ill not be
m ade quickly.
To use for drilling m etal
✷
In case you drill m etal w ith a m etal-w orking drill,
✁
apply in advance a center punch in the drilling
position. You can drill m etal stably since the point
of the drill does not slip.
If you apply sew ing m achine oil or soapy w ater to
✁
the drill w ith a brush or an old tooth brush, the
drill w ill last long.
Even if m ore-than-necessary force is used, a hole
✁
w ill not be m ade quickly.
On the contrary, the edge of the drill w ill be
dam aged. This w ill decrease operational efficiency
and shorten the life of this tool.
CAUTION:
Do not expose the m otor to w ater as it m ay cause
m otor m alfunction and electric shock.
5. To use the driving w ood screw s (FD10VB)
(1) Driver bit
For driving a slotted head w ood screw , the driver
✁
bit detaches easily. So use cross-recessed head
w ood screw s as often as possible.
Select a driver bit m atching the cross-recessed and
✁
the slotted groove of the w ood screw .
(2) Pilot hole
If a pilot hole is made with a drill a little smaller than
the diameter of the wood screw, the lumber will not
be split and the wood screw will be driven with ease.
(3) Driving operation
Put the w ood screw lightly in the pilot hole, apply
the bit to the screw head groove, turn on the sw itch
and drive the screw .
6. Caution to be taken immediately after operation
When placing the drill in dusty places before the
rotating parts has stopped com pletely, m ake sure
the m achine does not suck in dust and sw arf.
M AINTENANCE AND INSPECTION
CAUTION
Be sure to sw itch pow er OFF and disconnect the plug
during m aintenance and inspection.
1. Inspecting the drill bits and driver bit
Since use of an abraded drill bit will cause motor
malfunctioning and degraded efficiency, replace the
drill bit with a new one or resharpening without delay
when abrasion is noted. If you use a driver bit of
which point is worn or broken, it will be dangerous
since it slips. So replace it with a new one.
2. Inspecting the mounting screw s
Regularly inspect all m ounting screw s and ensure
that they are properly tightened. Should any of the
screw s be loose, retighten them im m ediately. Failure
to do so could result in serious hazard.
3. Servicing
Consult a Hitachi Authorized Service Center in the
event of pow er tool failure.
4. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Rem arks
CAUTION
Repair, m odification and inspection of Hitachi Pow er
Tools m ust be carried out by a Hitachi Authorized
Service Center.
This Parts List w ill be helpful if presented w ith the
tool to the Hitachi Authorized Service Center w hen
requesting repair or other m aintenance.
In the operation and m aintenance of pow er tools,
the safety regulations and standards prescribed in
each country m ust be observed.
M ODIFICATION
Hitachi Pow er Tools are constantly being im proved
and m odified to incorporate the latest technological
advancem ents.
Accordingly, som e parts (i.e. code num bers and/or
design) m ay be changed w ithout prior notice.
GUARANTEE
We guarantee Hitachi Pow er Tools in accordance w ith
statutory/country specific regulation. This guarantee does
not cover defects or dam age due to m isuse, abuse, or
norm al w ear and tear. In case of com plaint, please send
the Pow er Tool, undism antled, w ith the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
NOTE
Due to HITACHI's continuing program of research and
developm ent, the specifications herein are subject to
change w ithout prior notice.
English
5
Werbung
Inhaltsverzeichnis
