Ingersoll-Rand PROTECH 291 Bedienungsanleitung Seite 20

1 Motor Housing Assembly . . . . .
1A Plunger Bushing . . . . . . . . .
1B Reverse Valve Bushing . . .
2 Trigger . . . . . . . . . . . . . . . . . . . .
3 Trigger Pin . . . . . . . . . . . . . . . . .
4 Trigger Stop Pin . . . . . . . . . . . . .
5 Throttle Valve . . . . . . . . . . . . . .
6 Throttle Valve Plunger . . . . . . . .
8 Throttle Valve Spring . . . . . . . . .
9 Inlet Bushing Assembly . . . . . . .
10 Inlet Bushing O–ring . . . . .
11 Oil Chamber Plug Assembly . . .
12 Chamber Plug Seal . . . . . . .
13 Reverse Valve Assembly . . . . . .
14 Reverse Valve O–ring . . . .
15 Reverse Valve Stop Pin . . .
16 Reverse Valve Detent Spring . . .
17 Reverse Valve Detent Ball . . . . .
19 Reverse Valve Retaining Pin . . .
20 Backhead . . . . . . . . . . . . . . . . . .
21 Backhead Gasket . . . . . . . . . . . .
22 Backhead Cap Screw (4) . . . . . .
23 Lock Washer (4) . . . . . . . . . . . . .
24 Rear Rotor Bearing . . . . . . . . . .
25 Rear End Plate Assembly . . . . . .
26 End Plate Alignment Pin . .
27 Cylinder Assembly . . . . . . . . . . .
28 Cylinder Dowel (2) . . . . . .
29 Rotor . . . . . . . . . . . . . . . . . . . . .
30 Vane Packet (set of 5 Vanes) . . .
31 Front End Plate . . . . . . . . . . . . .
32 Front Rotor Bearing . . . . . . . . . .
33 Hammer Frame . . . . . . . . . . . . .
34 Hammer Cam . . . . . . . . . . . . . . .
35 Hammer . . . . . . . . . . . . . . . . . . .
36 Hammer Pin . . . . . . . . . . . . . . . .
37 Hammer Frame Washer . . . . . . .
38 Anvil Assembly
for 1" square drive . . . 291–A726
for 6" extended, 1"
square drive . . . . . . . . 291–A726–6
for spline drive . . . . . . 281–A526
* Not illustrated.
Indicates Tune–up Kit part.
PART NUMBER FOR ORDERING
REFERENCE POUR COMMANDE DE LA PIECE
BESTELLNUMMER
NUMERO DEL PEZZO PER L'ORDINAZIONE
SIMBOLO DE LA PIEZA PARA PEDIDOS
BESTELNUMMERS
291–A40 39
291–303
291–330
291–93 40
291–94
291–95
291–50 41 Hammer Case Assembly
291–302
291–51
291–A565
291–566
291–A427 42
291–428 43
291–A329 43A
291–338
291–332
291–334
291–333
291–336 44 Hammer Case Cap Screw (4) . . .
291–102 45 Lock Washer (4) . . . . . . . . . . . . .
291–739 47 Hammer Case Gasket . . . . . . . . .
291–103 48 Dead Handle . . . . . . . . . . . . . . . .
291–104 49 Dead Handle Cap Screw (4) . . .
291–24 50 Lock Washer (4) . . . . . . . . . . . . .
291–A12 51 Nameplate
291–10
291–A3
291–98
291–53
291–42–5
291–11 52 Nameplate Drive Screw (2) . . . .
291–25 * Tune up Kit (includes illustrated
291–703 items 5, 8, 10, 12, 14, 16, 17, 21,
291–721 24, 30, 32, 39, 40, 43 and 47) . .
291–724
291–704
291–706
20
Socket Retaining Ring
for 1" square drive . . . 291–425
for spline drive . . . . . . 281S–425
Socket Retaining Ring
for 1" square drive . . . 291–426
for spline drive . . . . . . 281S–426
for models 291, 291–6
and 291–S . . . . . . . . . . 291–A727
for models 291–EU
and 291–6–EU . . . . . . 291–EU–A727
Hammer Case Bushing . . .
Hammer Case Seal . . . . . . .
Warning Label
for models 291, 291–6
and 291–S . . . . . . . . . . 222–99
for models 291–EU
and 291–6–EU . . . . . . EU–99
for model 291 . . . . . . . 291–304
for model 291–EU . . . 291–EU–301
for model 291–6 . . . . . 291–301–6
for model 291–6–EU . 291–6–EU–301
for model 291–S . . . . . 291S–301
291–641
291–642
291–105
291–104
291–36
291–48
291–49
291–504
222–302
281–TK1