Hauff-Technik HSD-SSG Montageanweisung Seite 5

Standard-Ringraumdichtung HSD-SSG
• Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten
• Elastomere nach den geltenden Umweltvorschriften entsorgen.
• Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
• Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.
Safety instructions and informations
Target group
The installation may only be carried out by technical experts.
Qualifi ed and trained individuals carrying out installation must have
• k nowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfi lling utility trenches, as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the impermeable concrete directive and building waterproofi ng
standards as amended.
General information and intended use
According to their intended use, our products have been designed exclusively for
installation in buildings made from state-of-the-art construction materials. We do
not accept liability for use deviating from or beyond this unless our express written
confi rmation has been obtained in advance.
For warranty conditions, please see our current General Terms and Delivery
Conditions.
For sealing new pipes to be installed or pipes that have already been laid in core
drills or wall sleeves. Can be adapted to the most common cable diameters on
site. The standard press seal HSD 100-SSG is suitable for the installation and inser-
tion of 1 cable/pipe with outer diameter 18-65 mm or 25-63 mm, 70-112 mm or
75-110 mm for HSD 150-SSG, 110-162 mm or 110-160 mm for HSD 200-SSG,
159-211 mm for HSD 250-SSG and 200-252 mm for HSD 300-SSG.
Standard press seals are not fi xed settlement points or bearings and therefore
cannot absorb any mechanical forces. Any anticipated reductions must be
compensated for by the installation of centering guides in the conduits or core
drillings and/or by spacers.
Safety
This section provides an overview of all the main safety aspects for optimum
protection of personnel and a safe installation process. If there is a failure to
observe the instructions and safety information set out here, this may result in
signifi cant hazards.
Standard press seal installation must comply with the relevant professional
association regulations, VDE provisions, national safety and accident prevention
regulations as well as company regulations (work and procedural instructions).
The fi tter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to installa-
tion of the standard press seal: tion of the standard press seal:
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in signifi cant bodily harm and property damage.
• The nationally applicable laying and fi lling regulations for pipes and cables are
to be observed at all times.
• S eal the underground and cable substructure well prior to laying pipes/cables
so that the latter cannot subside.
NOTE!
No sealing due to incorrect assembly!
Improper installation can result in damage.
• For one-sided installation of the standard press seal into core drillings, seal
from outside of building.
• Prior to installing the standard press seal, any existing breaks or blowholes in
the cored hole have to be repaired.
• Ensure that the medium pipe is centred and horizontal in the core drilling/
wall sleeve.
• Please make sure that the inside of the liner is clean, dry and free of grease.
• The respective application range is specifi ed on the inside of the standard
press seal.
• If the press seal is installed in an exposed duct, then the duct wall must be
stabilised with a clamping strap at the location of the press seal.
• The front and rear press segments must be arranged offset.
• Do not lubricate the outer sealing surface of the press seal with lubrication.
• The pipe seal is evenly pressed in as soon as the rubber can be seen and felt
in all inspection openings.
• If sealing is to be carried out on the outside of the building, a check must be
carried out before the trench is fi lled and all laying and connection is com-
pleted to see whether the rubber in all inspection openings can be seen and
felt. If this is not the case or it is no longer possible to access the inspection
openings, the torque must be checked and if necessary tightened.
• No cleaning agents containing solvent may be used to clean the standard
press seal. We recommend using cable cleaner KR M.T.X.
• For details of other accessories and further information, see www.hauff-
technik.de and the technical specifi cation sheets.
EN
Personnel requirements
Qualifi cations
Risk of injury in case of inadequate qualifi cation!
Improper handling can result in signifi cant bodily harm and damage to property.
• Installation may only be carried out by qualifi ed and trained individuals who have
read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the relevant
provisions, standards and regulations, skilled experts are able to carry out the worked
assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport Safety instructions in connection with transport
NOTE!
Damage in the event of improper transport!
Signifi cant damage can occur in the event of improper transport.
• W hen unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport damage.
In the event of transport damage being visible from the outside, proceed as follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or delivery
note provided by the transporter.
Scope of delivery
The scope of delivery of the s HSD 100-SSG, HSD 150-SSG, HSD 200-SSG, HSD
250-SSG and HSD 300-SSG includes:
Storage
NOTE!
Damage due to improper storage!
Signifi cant damage can occur in the event of improper storage.
•
•
Disposal
If no return or disposal agreement has been concluded, recycle dismantled
components after they have been properly dismantled:
• Metal remains are to be scrapped according to existing environmental
regulations.
• Dispose of elastomer segments according to existing environmental regulations.
• Dispose of plastics according to existing environmental regulations.
• Dispose of packaging material according to existing environmental regulations.
Art. Nr.: 5090032038 Rev.: 04/2019-01-21
WARNING!
• Submit a claim for every defect as soon as it has been identifi ed.
• Make a note of the extent of damage in the transport documentation or
delivery note provided by the transporter.
Designation
HSD 100-SSG 18-65-SL
HSD 100-SSG 25-63
HSD 150-SSG 70-112-SL
HSD 150-SSG 75-110
HSD 200-SSG 110-162-SL
HSD 200-SSG 110-160
HSD 250-SSG 159-211-SL
HSD 300-SSG 200-252-SL
Protect the standard press seal from damage, damp and soiling prior to
installation. Only intact components may be installed.
T he standard press seal must be stored in such a way that it is not exposed
to low temperatures (<5° C), high temperatures (>30° C) or direct sunlight.
blind plug blind plug is
included available as
an optional
accessory
X
X
X
X
X
X
X
X
5