Maintenance And Servicing; Maintenance And Cleaning - Bosch POF 1200 AE Originalbetriebsanleitung

20 | English
Turn the centring screw (40) into the thread of the router
compass. Position the tip of the screw in the centre point of
the curve you want to rout; make sure the tip of the screw
reaches the surface of the workpiece.
Roughly set the required radius by moving the router com-
pass and tightening the wing bolts (37) and (38).
Then loosen the wing bolt (38) and use the knob (39) to
fine-adjust the length. One revolution corresponds to an ad-
justment range of 2.0 mm. Each of the graduation marks on
the knob (39) changes the adjustment range by 0.1 mm.
Switch the power tool on and move it over the workpiece us-
ing the right handle (2) and the handle for the router com-
pass (36).
Routing with the guide rail (see figure N)
You can use the guide rail (41) to rout in straight lines.
To level out the height difference, fit the spacer plate (42).
Fit the router compass/guide rail adapter (35) as shown in
the figure.
Fasten the guide rail (41) to the workpiece using suitable
clamping devices, e.g. screw clamps. Put the power tool
with the guide rail adapter (35) fitted on the guide rail.
Routing with the guide bushing (see figures O–P)
Using the guide bushing (43), you can transfer contours
from templates or patterns to the workpiece.
Select the guide bushing that is suitable for the thickness of
the template or pattern. Due to the protruding height of the
guide bushing, the template must have a minimum thickness
of 8 mm.
Move the release lever (20) and push the guide bush-
ing (43) into the base plate (6) from below. The coding
cams must audibly click into the recesses of the guide bush-
ing.
Select a router bit with a diameter that is smaller than
u
the interior diameter of the guide bushing.
To rout with the guide bushing (43), proceed as follows:
– Switch the power tool on and move it with the guide bush-
ing towards the template.
– Push the clamping lever for locking the routing
depth (16) down and slowly move the router down until it
reaches the set routing depth. Release the clamping lever
for locking the routing depth (16) again to lock this
depth. If necessary, push the clamping lever for locking
the routing depth (16) up to fully lock it.
– Move the power tool with the protruding guide bushing
along the template, applying pressure to the sides.

Maintenance and Servicing

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
1 609 92A 4N8 | (08.01.2019)
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
In extreme conditions, always use a dust extractor if
u
possible. Blow out ventilation slots frequently and in-
stall a residual current device (RCD) upstream. When
machining metals, conductive dust can settle inside the
power tool, which can affect its protective insulation.
After-sales service and advice on using products
Our after-sales service can answer questions concerning
product maintenance and repair, as well as spare parts. You
can find exploded drawings and information on spare parts
at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the type plate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or ar-
range the collection of a product in need of servicing or re-
pair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Bosch Power Tools