Ferax FKS-2000 Bedienungsanleitung Seite 8

GB
Class ll machine. Your machine is double
insulated; therefore no earthwire is required.
Whenever the machine is in use, safety
goggles must be worn to safeguard against
flaying object, as must ear protectors, such
as a soundproof helmet, in order to protect
the operator's hearing. If the operator is
working in an area where there is a risk of
falling objects, a safety helmet must also be
worn.
Wear gloves to protect your hands
Do not expose to rain
Wear safety boots to protect against electric
shock
Sound power level 104 dB (A)
Warning! Take care not to expose this tool to
rain and remove plug from mains
immediately if the supply cable is damaged.
1. Keep work area clean
Cluttered areas invite injuries. Do not start cutting
until you have a clear work area, secure footing,
and a planned retreat path from the falling tree.
2. Consider work area environment
Use extreme caution when cutting small sized
brush and sapling, as slender material may catch
the saw chain and be whipped toward you or pull
you off balance. Do not operate a chain saw in a
tree unless you are specifically trained to do so.
When cutting a limb that is under tension, be alert
for spring back so that you will not be struck when
the tension in the wood fibers is released. Do not
expose the chain saw to rain. Do not use the chain
saw in damp or wet locations. Do not use the chain
saw in the presence of flammable liquids or gases.
3. Store idle chain saw
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
4. Do not force the chain saw
The chain saw will do a better and safer job when
used at the rate for which it was intended.
5. Use the right tool
Cut wood only. Do not use the chain saw for
purposes for which it was not intended. For
example, do not use the chain saw for cutting
plastic, masonry, or non-building materials.
6. Dress properly
Do not wear loose clothing or jewelry, as they can
get caught in moving parts. Non-skid footwear
is recommended when working outdoors. Wear
protective hair covering to contain long hair.
7. Use safety gear
Use safety glasses, safety footwear, snug fitting
clothing, protective gloves, and protective hearing
8
and head gear.
8. Carrying the saw
Carry the saw by the front handle with the saw
stopped. Keep your finger off the switch, and
make sure that the guide bar and saw chain are to
the rear.
9. Do not abuse the cord
Never carry the tool by the cord or yank it to
disconnect it from the socket. Keep the cord away
from heat, oil and sharp edges.
10. Secure work
Use clamps or a vice to hold the work.
11. Do not overreach
Keep proper footing and balance at all times.
12. Maintain the chain saw with care
Inspect the chain saw cords periodically and, if
damaged, have them repaired by an authorized
service facility. Keep the cord clear of the chain
and operator at all times. Never carry the saw by
the cord or pull it to disconnect from receptacle.
Keep the cord from oil and sharp edges. Inspect
the extension cords periodically and replace if
damaged. Keep tools sharp and clean for better
and safer performance. Follow instructions for
lubricating and changing accessories. Keep
handles dry, clean and free from oil and grease.
13. Disconnect the chain saw
Disconnect the chain saw when not in use, before
servicing, and when changing accessories and
attachments such as saw chain and guard.
14. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
15. Avoid unintentional starting
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
16. Use outdoor extension leads
Use only extension cords that are intended for
outdoor use and which are so marked (≥ 1,5
mm2).
17. Stay alert
Watch what you are doing. Use common sense.
Do not operate the chain saw when you are tired.
Keep all parts of your body away from the saw
chain when the motor is operating. Before you
start the saw, make sure the saw chain is not
contacting anything.
18. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and
perform its intended function. Check for alignment
of moving parts, free running of moving parts,
breakage of parts, mounting and any other
conditions that may affect its operation. A
guard or other parts that is damaged should be
properly repaired or replaced by an authorized
service center unless otherwise indicated in
this instruction manual. Have effective switches
replaced by an authorized service facility. Do not
use the tool if the switch does not turn it on and off.