Safety Instructions - Chicago Pneumatic CP7600xC Bedienungsanleitung

oil; i.e. drops of oil can be dropped either into the compressed air
or directly into the air inlet.
The trigger, planetary gears, needle bearings and ball bearings
should be lubricated with grease during the regular overhaul of
the machine.
The angle gear and clutch must be lubricated using grease that
contains molybdenum disulphide: Molykote BR2 Plus, for ex-
ample, or an equivalent brand.
Use lubricants of good quality. The oils and greases mentioned
in the table are examples of lubricants which are recommended.
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles cause rust
and sticking of vanes, valves etc. An air filter should be installed
close to the machine (see "Air quality").
Service instructions
Overhaul and preventive maintenance is recommended at regular
intervals once per year or after maximum 250.000 tightenings de-
pending on which occurs sooner. More frequent overhaul may be
needed, if used at high torque and long tightening times. If the
machine not is working properly, it should immediately be taken
away for inspection.
The strainer at the air inlet and the exhaust silencer should be
cleaned frequently or replaced in order to prevent clogging, which
decreases the capacity.
At the overhauls, all parts should be cleaned accurately and de-
fective or worn parts (i.e. O-rings, vanes) should be replaced.
Disassembling / assembling
It is important that the machines threaded connections are tightened
properly; i.e. in accordance with the specifications on the exploded
views.
A
Lubricate o-rings and threaded connections with grease before
assembling.
Cleaning
Clean all parts thoroughly in white spirit or similar cleaning agent.
To prevent clogging and decreased power, it could be necessary
to clean the strainer (if used) and the exhaust filter between the
overhauls.
Inspection
After the cleaning, inspect all parts. Damaged and worn parts
should be replaced.
Lubrication
Lubricate specially gears, valve and clutch with grease containing
molybdenum disulphide (e.g. Molykote BR2 Plus). Please see
exploded views and fig. under Service instructions.
EN
Grease guide Nutrunners
Brand Bearings
BP
Castrol Spheerol EP L2
Esso Beacon EP2
Q8 Rembrandt
EP2
Mobil M.Grease XHP
222
Shell Alvania EP2
Texaco Multifak EP2
Molycote
Lubricating
STP
Brand
Bp
Castro
Esso
Q8
Mobil
Shell
Texaco
Molycote

Safety instructions

Warning
Make sure you are familiar with the operating instructions before
you use thi machine.
The machine, together with any attachments and accessories,
must never be used for anything other than the designated purpose.
All locally legislated safety rules with regard to installation,
operation and maintenance shall be respected at all times.
Refer installation and servicing to qualified personnel only.
Before making any adjustments (e.g. changing sockets) discon-
nect the machine from the compressed air line.
Check the direction of the rotation before using the machine.
Operators of nutrunners with a torque reaction bar should take
particular care to avoid injuries due to squeezing. For safety reasons
– never allow anyone to operate the machine unless he is trained
and thoroughly familiar with how the machine works in different
circumstances. Refer to the section headed "Reaction bar".
The machine may only be used together with the associated
torque reaction bar which is adapted to the screw joint application
concerned. See also the instructions under the heading "Reaction
bar".
Never put your hand on or close to the reaction bar while
the machine is being used.
Check that the power socket is properly fastened. Replace the
retaining or locking pin when necessary. Also replace any worn
socket.
Part no 8940164682
Issue no 0
Series no 1
Date 2008-06
Page 7
Free wheel
unit (gear rim
and gear
wheels)
Energrease LS-
EP2
Beacon EP2
Rembrandt
EP2
Alvania EP2
Suntemp LE
9102
Oil treatment
Gears General purpose
Energrease LS-EP2
Spheerol EP L2
Beacon EP2
Rembrandt EP2
Mobilegrease XHP
222
Alvania EP2
Multifak EP2
BR2 Plus
Free wheel