JB Systems MIX2 Bedienungsanleitung Seite 4

ENGLISH
FUNCTIONS (FRONT)
1. MIC INPUT GAIN: Adjusts microphone input level.
2. HIGH AND LOW EQ: Adjusts the high and low frequency levels of the input channels for a good sound.
3. INPUT FADER: Controls individual source levels (channels) in the mix.
4. REPLACEABLE CROSSFADER: Achieves clean segues between the two input channels. "Hard left"
selects Channel 1. "Hard right" selects Channel 2. With the crossfader centered, both assigned
channels are live. Use the crossfader for fast and seamless segues (fades) frome one selected channel
to the other. Note: The crossfader is user replaceable in case of failure. Simply unscrew the two large
screws which hold it in place, lift it out and disconnect the cable. Re-attach the new crossfader and
screw the mounting plate back on the unit.
5. MIC INPUT: Insert your microphone here with 1/4" plug.
6. HEADPHONE INPUT: Insert your headphones here with 1/4" plug.
7. INPUT TOGGLE SWITCH: Selects which source will be active based on what you have connected to
the rear panel input section.
8. CUE PAN: Used to preview channel audio to your headphones. Listen here before moving up channel
faders or moving the crossfader.
9. HEADPHONE LEVEL: Adjusts cue volume.
10. MASTER FADER: Controls the overall output level.
11. CHANNEL GAIN: Adjusts the pre-fader volume for cleaner sound.
12. FADER START ON/OFF SWITCH: When you have a compatible CD-player connected to the fader
control connectors, you can control its start/stop (re-cue) functions with the cross fader. With this switch
you can turn the fader start control on and off
JB SYSTEMS
®
OPERATION MANUAL
3/32
ENGLISH
FUNCTIONS (rear)
13. FADER CONTROL: When connected to these inputs, compatible CD-players can be controlled by the
fader starts of this mixer.
14. POWER SWITCH: Turns the unit ON and OFF.
15. POWER CONNECTOR: Plug in power adapter here and check the voltage level to match your
country's standard.
16. PHONO/LINE SWITCH: This switch makes it possible to switch between the Line and Phono level for
these inputs.
17. PHONO / LINE INPUTS: each used to connect two different audio signal levels. Refer to switch (16) to
change one line input to phono level. Use this position only for turntables. Line level sources will
overload the sensitive phono pre-amps and will cause distortion.
18. LINE INPUTS: Unbalanced RCA jacks for connecting stereo audio from line level sources such as CD
players, Hi-fi VCR's, cassette and reel-to-reel tape decks, DAT machines, tuners, even synthesizers or
other mixing consoles.
19. MASTER OUTPUT: Unbalanced RCA connectors controlled by the master fader.
20. RECORD OUTPUT: Carries the same signal as the master outputs but is not influenced by the master
level control. Used to connect analog recording equipment.
CROSSFADER STARTS
The crossfader integrates the optical fader start switches. These fader starts are compatible with all current
JB Systems CD-players. This is how it works:
A. CROSSFADER IN LEFT POSITION:
CD-player connected to fader start connector A is playing,
the other CD-player is paused.
B. CROSSFADER MOVES TO THE RIGHT:
CD-player connected to fader start connector A stops
playing, returns to its previously programmed cue point
and waits in pause. The other CD-player starts playing
from its previously programmed cue point.
C. CROSSFADER IN RIGHT POSITION:
CD-player connected to fader start connector B is playing,
the other CD-player is paused.
D. CROSSFADER MOVES TO THE LEFT:
CD-player connected to fader start connector B stops
playing, returns to its previously programmed cue point
and waits in pause. The other CD-player starts playing
from its previously programmed cue point.
Important: Both fader start switches must be in "ON" position!
MIX2 JB SYSTEMS 4/32
®
OPERATION MANUAL
MIX2