Synq DLP-6 Bedienungsanleitung Seite 8

ENGLISH
if it should be on or off, simply turn the DIAL (4) to select.
 EQ BAND: turn the DIAL (4) to choose the desired EQ-filter: you can choose 1 to 6.
 EQ TYPE: turn the DIAL (4) to choose the desired EQ-filter type:
 PEQ: Parametric equalizer, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the center frequency from 19,7Hz to 20kHz.
o BANDWIDTH: turn the DIAL (4) to change from 0,016 (narrow) to 4,000 (wide).
 LS1: Low-shelf 6dB, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the frequency from 19,7Hz to 2kHz.
 LS2: Low-shelf 12dB, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the frequency from 19,7Hz to 2kHz.
 HS1: High-shelf 6dB, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the frequency from 3886Hz to 21,9kHz.
 HS2: High-shelf 12dB, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the frequency from 3886Hz to 21,9kHz.
INPUT PARAMETERS – LINK SETTINGS
You can link the settings of input channels A and B so you only have to setup one input (A or B)  all
settings of the other input will be identical at all times. Turn the DIAL (4) to set the link ON or OFF and press
the SAVE-button (11). You will be asked if you are sure: press the /buttons (9&10) to choose OK or
CANCEL and press the SAVE button (11) again to confirm.
INPUT PARAMETERS – COPY SETTINGS
You can copy the settings between the input channels ("A to B" or "B to A"). This means that only the
ACTUAL SETTINGS are copied, there will be no constant synchronization between the channels! This is
what you can do:
 DON'T COPY: press the /buttons (9&10) to go to another parameter setting.
 COPY: press the SAVE button (11) to confirm copying  all settings will be copied between the inputs.
OUTPUT PARAMETERS – GAIN + PHASE + SOURCE
Used to adjust the gain and phase of the 6 outputs. For each output you can also select to which input it
should be linked. Use the /buttons (9&10) to jump between the different parameter settings:
 OUTPUT GAIN: turn the DIAL (4) to adjust the input gain from -40dB to +12dB in 0,1dB steps.
 PHASE: turn the DIAL (4) to choose "+" (output in phase) or "-" (output in anti-phase)
 SOURCE SELECT: turn the DIAL (4) to select the input that should be linked to the selected output:
 OFF: selected output is not used.
 A: selected output is linked to input A.
 B: selected output is linked to input B.
 A+B: selected output is linked to inputs A and B.
OUTPUT PARAMETERS – DELAY
The display shows the delays in meter, milliseconds and foot. You can choose delays up to 2000ms or
688,52m!
 SMALL STEPS: turn the DIAL (4) to adjust the delay in small 21µs steps.
 BIG STEPS: press the /buttons (9&10) to adjust the delay in big 5,20ms steps.
OUTPUT PARAMETERS – EQUALIZER
All output channels have a 4band EQ, each band can have different settings. Use the /buttons (9&10) to
jump between the different parameter settings:
 ON/OFF: for each band you can choose if it should be on or off, simply turn the DIAL (4) to select.
 EQ BAND: turn the DIAL (4) to choose the desired EQ-filter: you can choose 1 to 4.
 EQ TYPE: turn the DIAL (4) to choose the desired EQ-filter type:
 PEQ: Parametric equalizer, with the following parameters:
o GAIN: turn the DIAL (4) to adjust the gain from -30dB to +15dB in 0,1dB steps.
o FREQ: turn the DIAL (4) to adjust the center frequency from 19,7Hz to 20kHz.
SYNQ
®
6/96
OPERATION MANUAL
DLP-6 MK2