Stereo Link - LD Systems MAUI P900 Bedienungsanleitung

If connection is successfully established between the slave unit and the master unit, the green STEREO LINK LED on the slave unit lights up
permanently and the blue Bluetooth LED flashes slowly (approximately 0.3 Hz). During the pairing process, the green STEREO LINK LEDs of both
systems flash rhythmically at a frequency of about 3 Hz. The left channel of the stereo signal is reproduced by the master unit and the right
channel by the slave unit.

STEREO LINK

7
A. Stereo system with 2 x MAUI P900 and 1 x Bluetooth playback device: Pair the desired Bluetooth playback device with the left MAUI P900
system. The left system automatically becomes the master unit (press HOLD TO LINK for 3 seconds). If necessary, disconnect an existing
Bluetooth connection with a Bluetooth playback device on the right MAUI P900 system (Press and hold HOLD TO LINK and STEREO LINK
simultaneously for one second). To pair the right MAUI P900 system with the master unit, press and hold the STEREO LINK button on both
devices for approximately 3 seconds within 30 seconds. The right system automatically becomes the slave unit (max. distance 15 m). The
master unit transmits the left channel of the stereo signal from the Bluetooth device and the slave unit the right channel.
B. Stereo system with 2 x MAUI P900 without Bluetooth playback device: Disconnect any existing Bluetooth connection between the slave
unit and a Bluetooth playback device by pressing and holding both buttons HOLD TO LINK and STEREO LINK on the slave unit simultane-
ously for approximately 1 second. When pairing two MAUI P900 systems, ensure that the distance between the systems is no more than 15
metres. Press and hold the STEREO LINK button on the master unit for approximately 3 seconds and press the STEREO LINK button twice in
quick succession on the slave unit. Pairing occurs automatically within approximately 30 seconds. The master unit transmits the left channel
of the stereo signal from a Bluetooth playback device and the slave unit the right channel. Pairing a Bluetooth playback device with the
master unit can now be done later.
Please note:
• When the MAUI P900 systems have been switched off and back on, the Bluetooth playback device will pair automatically and the systems
will connect with each other automatically.
• To cancel a Bluetooth connection between a Bluetooth playback device and a STEREO LINK connection, press and hold the HOLD TO LINK
(No. 5) and STEREO LINK (No. 7) buttons simultaneously for about 1 second. This deletes the entire list of paired devices (factory setting).
• The maximum number of paired Bluetooth devices is 8 (including paired MAUI P900 systems). If another device is paired, the last entry
from the list of stored devices will be deleted. A maximum of 1 playback device and 1 MAUI P900 system can be connected simultaneously
with a Bluetooth unit as a stereo extension.
For information regarding the operation of the Bluetooth and stereo link module and the different Bluetooth and stereo link operating modes,
please refer to the following tables.
Operation of Bluetooth and stereo link module
Pair Bluetooth unit with playback device
Pair stereo link – master unit
Pair stereo link – slave unit
(playback device paired with master unit)
Pair stereo link – slave unit
(no playback device paired with master unit)
Reset
Bluetooth and stereo link status
Pair Bluetooth unit with playback device
Bluetooth unit is paired and connected only with playback device
Pair Bluetooth unit with playback device (as stereo link – master)
Pair slave unit – stereo link to master unit
Slave unit – stereo link paired with master unit
Slave unit – slave unit paired but not connected
Master unit – stereo link pairing without Bluetooth connection to playback
device
Master unit connected to slave unit but without Bluetooth connection to
playback device
Master unit – stereo link pairing with Bluetooth connection to playback device
Master unit connected to slave unit with Bluetooth connection to playback
device
Neither Bluetooth nor stereo link connection
HOLD TO LINK STEREO LINK
Press for 3 seconds
Press for 3 seconds
Press for 3 seconds
Press briefly twice
Press simultaneously for 1 second
Bluetooth LED (blue) STEREO LINK LED (green)
Flashes (3 Hz) off
on permanently off
Flashes (3 Hz) on permanently
Flashes (0.3 Hz) Flashes (3 Hz)
Flashes (0.3 Hz) on permanently
Flashes (0.3 Hz) off
off Flashes (3 Hz)
off on permanently
on permanently Flashes (3 Hz)
on permanently on permanently
off off
7