DeWalt DE3000 Anleitung Seite 27

• Lock the clamps using the nuts (59). Do not overtighten. At this stage,
the saw must simply not come off the mounting plate when turning it over.
• Keep the rear end of the clamps within the dotted line as shown.
• Turn the saw mounting plate (18) over leading the cord into the table.
Make sure the mounting plate is flush with the worktop and tighten the
four fixing screws (19).
Adjusting the circular saw (the saw blade) (fig. A2, B & C)
When using the same saw all the time in the combi-table, this adjustment
only needs to be done once.
For high precision cuts, always adjust the saw to the parallel
fence, never to the lines on the table top.
• Slide the parallel rip fence (20) to the outer edge of the slot (34) in the
cutting insert. Adjust the fence as described above.
• Measure the distance from the saw blade to the fence at both ends of
the saw blade (refer to drawing C).
• The distance should be the same at both ends.
If not, adjust as follows:
• Slightly slacken the nuts (59) of the spring-loaded clamps and the
nuts (37) of the brackets (38).
• To adjust the blade, slightly move the saw.
• Check again.
• Tighten all nuts securely.
• Check that the blade is at right angles to the table surface
using a set square. (If adjustment is required, refer to the
instruction manual of the saw).
• For adjustment of the riving knife, also refer to the instruction
manual of your circular saw.
Rotate the blade manually to check that the blade does not
scratch the cutting insert or the saw blade guard.
The zero on the scale should coincide with the edge of the saw blade.
If required, adjust the scale.
• Loosen the two screws which hold the scale and adjust the scale in
the slots.
Removing your circular saw (fig. A2 & B)
• Slacken the four fixing screws (19) in the saw mounting plate (18) and
turn the mounting plate with circular saw upside down.
Do not slacken the fixing screws more than two turns.
• Slacken the clamps (39) only.
• Lift your circular saw away without changing the adjustment.
Depth of cut adjustment
For depth of cut adjustment, refer to the instruction manual of
your saw. Bear in mind that the maximum cutting depth is
reduced by approx. 10 mm when the circular saw is used as a
stationary tool.
For optimum results, allow the saw blade to protrude from the
workpiece by about 3 mm.
Bevel adjustment (fig. D)
To make bevel cuts with the combi-table, the cutting insert needs to be
replaced. Your DE3000 combi-table is supplied with 1 standard cutting
insert and 4 bevel cutting inserts to suit various bevel angles. The inserts
are marked A, B, C and D.
19
The table below shows which insert to use for your saw at specific bevel
angles.
Cutting insert, angles in degrees
D WALT DW62
E
D WALT DW365
E
D WALT DW86
E
Elu MH151
Elu MH165
Elu MH265
Elu MH85
Elu MH286
Bosch GKS 65
Bosch GKS 66 CE
Metabo KsE 1668s-Signal
Metabo Ks 1468 S
Metabo Ks 1266 S
For D WALT DW365 only
E
To make mitre cuts with the DW365, the attached plastic support is
required. The maximum depth of cut is reduced to 47 mm.
Due to the construction of the DW365, you cannot release the depth of cut
of the saw down to zero, which is necessary to replace the standard cutting
insert (23) to the appropriate bevel cutting insert. With the mounted plastic
support you can change the inserts without any problem.
• Remove the mounting profile (36) and one of the clamps (39)
underneath the saw mounting plate.
• Slide two of the plastic supports into each of the grooves near the slot
(34) facing the high edges to the outside of the mounting plate.
• Mount the clamp (39) and the profile (36) back to the plate.
• To hold the DW365 properly, you need to turn the metal brackets (38)
to the other side. Unscrew the nuts (37) and turn the brackets around.
Attention:
You must swap the left brackets with the right ones.
• Open the lower guard of the DW365 and insert the saw blade into the
slot (34) by placing the saw onto the plastic supports.
• To get the parallel adjustment of the saw blade to the slot (34), place
the edge under the saw base-plate against the edge of the support.
(additional adjustment of the saw is not required).
• Place the brackets (38) and the mounting profile (36) as described in
the instruction manual.
• Place and adjust the clamps (39) as described in the instruction
manual.
• Tighten all nuts securely.
Set the depth of cut of your saw to 0 mm.
• Loosen the screw (44) and pull out the cutting insert (23).
• Slide the new cutting insert into the saw mounting plate and tighten the
screw (44).
Adjust the bevel angle of your saw.
• Move the saw blade up through the slot in the new cutting insert and
adjust the depth of cut.
• Never use the saw table without the appropriate cutting insert.
• Rotate the blade manually to check that the blade does not
scratch the cutting insert or the saw blade guard.
E N G L I S H
A B C
3-11 19-31 34-45
8-15 18-24 26-33
7-13 18-29 27-35
12-23 24-39 41-45
9-18 18-30 30-40
8-15 18-24 26-33
9-18 21-30 31-39
7-13 18-29 27-35
8-21 21-32 33-41
8-21 21-32 33-41
19-36 38-45 -
19-36 38-45
19-36 38-45
D
-
38-45
40-45
-
41-47
38-45
-
40-45
45
45
-
en - 4