Numark NDX900 Kurzanleitung Seite 3

4. TRAKTOR LE 2 SETUP
1. With the NDX900 connected to the computer through USB, launch TRAKTOR LE 2.
2. Next, in TRAKTOR LE 2, go to Help > Start Setup Wizard.
3. In the window that opens, click Next to get to the Traktor LE2 Controller Selection.
4. Next to Are you using an external controller? select Yes, then click Next.
5. Set manufacturer to Numark. If are using two NDX900 Controllers, set model to NDX900 LE Dual Deck.
If you are using a single NDX900, set model to 'NDX900 LE Single Deck' and click Next.
6. In the Mixer Setup page next to Are you using an external mixer? Select No.
7. Click Next and review the settings you have chosen.
8. Click Finish.
TRAKTOR LE 2 Audio Setup (PC)
1. Go into the Preferences menu in TRAKTOR LE 2 to configure the Audio Setup.
2. Go to File > Preferences.
3. In the Audio Device area if you are on a Windows platform, make sure that ASIO4ALL is selected. Click on the
Settings button to open the ASIO4ALL dialog box. Make sure the status under USB Audio Device is 'active'
(highlighted in blue) and then close out of the box. This will allow audio output from TRAKTOR LE 2 to be sent
through the USB connection to the NDX900 and output through its USB Audio RCA output.
4. To set up your audio input and output configuration click on Output Routing on the left-hand side of the
preferences window
5. Under Mixing Mode, choose External.
6. Under Output Deck A, choose USB Audio Codec 1 for 'L' and USB Audio Codec 2 for 'R'.
7. Under Output Deck B, choose USB Audio Codec 1 for 'L' and USB Audio Codec 2 for 'R'.
If using 2 NDX900 decks:
• Under Output Deck A, choose USB Audio Codec 1 for 'L' and USB Audio Codec 1 for 'R'.
• Under Output Deck B, choose USB Audio Codec 2 for 'L' and USB Audio Codec 2 for 'R'.
TRAKTOR LE 2's Audio Setup (Mac)
1. Click the TRAKTOR LE 2 menu in the upper-left of the screen, and select Preferences.
2. On the left-hand side of the window that opens, click the + next to Audio Setup.
3. Next, under Audio Setup on the left, click Soundcard.
4. On the right-hand side of window, next to Audio Device, select Aggregate Device.
5. On the left-hand side of the TRAKTOR preferences window, under Audio Setup on the left, click Output Routing.
6. On the right-hand side of window, next to Mixer Mode, select External.
7. Next to Out Channel A, for Left, select Aggregate Device Out 1. For Right, select Aggregate Device Out 2.
8. Next to Out Channel B, for Left, select Aggregate Device Out 1. For Right, select Aggregate Device Out 2.
If using 2 NDX900s, for the Left, select Aggregate Device Out 3. For Right, select Aggregate Device Out 4.
TRAKTOR LE 2 Controller Manager Setup
If you are using a single NDX900:
Setup your NDX900 to control a Deck in TRAKTOR LE 2:
1. Click on Controller Manager on the left-hand side of the Preferences window.
2. Next to Device, select NDX900 Single Deck Controls.
3. Under In-Port, select Numark NDX900.
4. Under Out-Port, select Numark NDX900.
5. Next to Device Target, select Focus.
6. The NDX900 will control whichever deck is focused (selected) on the TRAKTOR LE 2 main screen.
7. To change which deck is focused, you can either click the RECALL button in the upper-right corner of the NDX900
hardware, use your keyboard or mouse to select deck A or B from within the TRAKTOR LE 2 software.
8. Click Close.
If you are using two NDX900 units:
1. Click on Controller Manager on the left-hand side of the preferences window.
2. Next to Device, select NDX900 Deck A Controls (whichever deck you connected to the computer first will
become 'Deck A'.)
3. Under In-Port, select Numark NDX900.
4. Under Out-Port, select Numark NDX900.
5. Next to Device, select NDX900 Deck B Controls.
6. Under In-Port, select Numark NDX 900 #2.
7. Under Out-Port select NDX 900 #2.
8. Click Close.
TRAKTOR LE 2 Setup Wizard
3