Chicco polly swing up Gebrauchsanleitung Seite 19

to remove the batteries from their compart-
ment.
re
• Only use alkaline batteries of the same type
or equivalent to the type recommended for
ly
the correct function of this product. (for the
remote control: LR03-AAA; for the vibration
se
block: LR20-D; for the side fixture: LR14-C).
di-
• The use of rechargeable batteries is not
recommended as the product may not work
or
properly.
ts
• Rechargeable batteries must only be re-
he
charged under adult supervision.
a-
• Rechargeable batteries must be removed
from the product during recharging.
or
• Remove the batteries from the product be-
he
fore disposing of the product.
er,
• Always keep batteries and tools out of the
reach of children.
an
• To replace batteries: loosen the screw on the
he
battery compartment cover with a screwdriv-
er and open the cover. Then remove the spent
oy
batteries and fit new ones, ensuring that they
ps:
have been fitted in the correct polarity (as
n-
shown on the product), replace the battery
n.
cover, and tighten the screw.
nd
This product complies with EU Directive 2002/96/
EC.
The crossed bin symbol on the appliance indicates
ed
that the product, at the end of its life, must be dis-
posed of separately from domestic waste, either by
wn
taking it to a separate waste disposal site for electric
and electronic appliances or by returning it to your
dealer when you buy another similar appliance. The user is respon-
e-
sible for taking the appliance to a special waste disposal site at the
es
end of its life. If the disused appliance is collected correctly as sepa-
rate waste, it can be recycled, treated and disposed of ecologically;
this avoids a negative impact on both the environment and health,
a-
and contributes towards the recycling of the product's materials.
For further information regarding the waste disposal services avail-
n; able, contact your local waste disposal agency or the shop where
you bought the appliance.
nic
to CARE AND MAINTENANCE
Fabric composition
LINING COVER: All new materials. Outer cover: 100% polyester.
eir
Padding: 100% polyester.
BOOSTER CUSHION: All new materials. 100% polyester outer
cover. 100% polyester padding.
as
TOY: All new materials. 100% polyester.
p-
• This product requires periodic maintenance.
• The cleaning and maintenance operations must only be carried
nd
out by an adult.
e.
• Periodically inspect the swing to check for broken, torn or missing
he
parts: if this is the case, do not use it.
• Please refer to the care label for instructions on how to wash the
en
fabric parts.
Hand wash in cold water
ed
ed
30° C Do not bleach
Do not use a dryer
Do not iron
Do not dry clean
• Check that the fabric and stitching are in good condition each
time you wash it.
• Prolonged exposure to direct sun light or heat may cause the fab-
ric to fade or parts to deform.
Clean the frame structure with a damp cloth and neutral detergent.
Do not soak the frame in water.
Removable covers
• Remove the tray by pressing the two orange side buttons whilst
pulling it upwards.
• Remove the head rest and booster cushion, slide out the harness
straps through their holes.
• Slide the waist strap out through the plastic rings located at the
bottom of the seat.
• Unhook all the elastic rings from the plastic hooks on the bottom
side of the seat. Now remove the harness straps fastened to the
bottom of the fabric backrest, sliding them through the slots on
the outer edge of the seat. Now undo the zip, slide the upper
straps through the padding and remove the fabric part.
• To refit the cover on the frame, repeat the above procedure in
the reverse order, making sure that you hook all the elastic rings
back onto their relative hooks to ensure the padding is fastened
correctly to the frame.
COMPONENTS
a. Top tube of the seat
b. Frame connection tubes
1. Side sun hood hooks
c. Side fixture X (with remote control)
1. Battery compartment
d. Side fixture Y
e. Front and rear legs
f. Seat
1. Side backrest adjuster button
2. Vibration block
3. Fabric crotch strap
4. Side compartment for the connection tube
5. Connection fixture for the dual tray
g. Dual tray
1. Side button
2. Rigid crotch strap
3. Tray
4. Second tray
h. Booster seat
i. Waist strap
j. Upper harness strap
k. Remote control
l. Sun hood
m. Toys
ASSEMBLING THE FRAME
1. Grasp the front and rear legs, and insert them into the X and Y
fixtures on the tubes, as seen in Diagram 1. When the legs are
assembled correctly, the metal pins will slot into the holes on
the fixture tubes. At this point you will hear them click into place.
2. Press the fixture side buttons (Diagram 2) and open the frame by
pushing the front and rear legs apart. The seat can now be fitted.
ASSEMBLING THE SEAT
3. Open the zip on the back of the fabric backrest as far as possible
(Diagram 3) and slide the upper seat tube into the slots inside
the backrest, as seen in Diagram 4. Make sure you hear the metal
pins click into place.
4. Thread the upper harness straps through the slots in the backrest
(Diagram 5). Now cover the upper tube with the fabric and close
the zip (Diagram 6).
5. Hook all the elastic rings onto the plastic hooks on the bottom
19