G21 Chamber Gebrauchsanweisung Seite 4

PleASe CleAn THe PARTS THAT ConTACT FooD THoRouGHly BeFoRe eACH uSe
oF THIS APPlIAnCe.
Instructions
Start / Stop button:
when you press this button the appliance starts to work. It automatically stops after 20 minutes. If
you need to stop in the midway, just press this button again.
Reversal button:
if the appliance stops, press the reverse button. It is necessary to hold this button at least 3 se-
conds.
Sliding stall:
Adjusting soft and hard food materials. If processing soft materials move the sliding stall to soft
and vice versa. If you need to dismantle feeding tube from the main body, please toggle sliding
stall to "unlock" and keep on, at the same time revolve feeding tube clockwise. you will not be able
to dismantle feeding tube when sliding stall is not in place.
Method of use
1
Please install and use according to following steps:
1
2
Juice function
1. Connect the feeding tube with main body.
• Aim the feeding tube at the marking
• Revolve feeding tube counterclockwise from
2
click sound, it means that feeding tube has been installed correctly.
Aim the hexagonal screw shaft at the hole on main body, then push
it to the bottom.
2. Insert squeezing screw into the hole on the main body.
3. Insert squeezing cone into the feeding tube.
Pay attention to two salient on juice cone. Aim them at corresponding
3
indentation in feeding tube.
4. Install the cover of the feeding tube on feeding tube.
• Aim three lock buckle on cover of feeding tube at three corre-
sponding gaps on feeding tube, then push feeding tube cover to the
bottom horizontally.
• Revolve feeding tube cover counterclockwise until
4
the feeding tube cover aim at
1
Feeding tube cover must be installed in place, otherwise it could fall off
2
during working process.
5. Place Juice container with handle under the juice outlet.
• Put the juice container onto the plate.
Juice container should not be too full, otherwise juice could overflow
5
when you take out the juice container.
6. Put the pulp container under the pulp outlet nearing to juice con-
tainer.
7. Mount the tray on the top of the feeding tube. Tray is convenient to
add material, specially little granule food material like grapes, strawbe-
rries and so on.
on main body.
to . If you hear
marked on
marked on the feeding tube.
8. Connect power cord. Power cord must be connected firmly to avoid
6
loosing that may cause danger.
9. Pluck out the juice mouth cover to the left, open the mouth.
10. Wash the fruit and cut them into pieces which can be put into the
feeding tube.
If materials have core hard seed thick skin and hard shell please remove
them before processing. Spinach should cut into several pieces when
7
you squeeze them, properly control process speed.
Don't squeeze lemon directly.
11. Move sliding stall according with food material character. If food
material is soft, please toggle to "soft" stall, like tomato, orange and so
on; If food material is hard, please toggle to "hard" stall, like carrot; you
can toggle to middle stall excepting the foregoing description material.
8
12. Press the "Start / Stop" button, appliance starts to work. Appliance
has intelligent protection chip, it will automatically stop after working
20 minutes. If you need stop working in the midway, press the button
again.
13. Put food materials into the feeding inlet, and then push them into
feeding inlet gently by using the food pusher. Do not press food pusher
too strong. Do not put fingers or other objects into feeding tube. When
9
pulp or material were blocked, press "Reverse" button and keep on,
let food material go back automatically, or switch the appliance off and
clean the residue pulp in feeding tube.
14. After finishing, shut down switch and the power when juice outlet
has no flowing juice, taking the juice container and pulp container away
the juice outlet and pulp outlet after motor and screw rod ceasing, then
you can enjoy the fresh juice.
10
11 12
Images used in this manual are for illustrational purposes only and may differ from the actual
14
13
product.