Bosch PMF 350 CES Originalbetriebsanleitung Seite 19

Application tool
Bi-metal segment
serrated blade
TC-Riff sanding fin-
ger
TC-Riff plunge cut
saw blade
HCS universal joint
cutter
Bi-metal plunge cut
saw blade for wood
and metal
Bi-metal plunge cut
saw blade for wood
and metal
TC plunge cut saw
blade, metal
HCS plunge cut
saw blade for wood
Fitting/changing the application tool (AutoClic)
(see figures A–B)
Remove the application tool if one has already been fitted.
To do so, open the AutoClic lever (1) all the way. The applic-
ation tool/accessory will be ejected.
Place the required application tool (e.g. plunge cut saw
blade (9)) on a level surface so that the depressed centre is
face down (see figure on the graphics page; you should be
able to read the text on the application tool from above).
Turn the application tool to a position which is convenient
for the job at hand. Press the power tool onto the application
tool at the required angle until it audibly engages.
Check that the application tool is seated securely. Ap-
u
plication tools that are attached incorrectly or are not se-
curely fixed in place may come loose during operation,
thereby putting you at risk.
Bosch Power Tools
Material Application
Insulation material, insula- Precise cutting of soft materials;
tion boards, floor panels, example: Cutting insulation boards to size, cutting pro-
impact sound insulation truding insulation material to length so that it is flush with
boards, cardboard, car- the surface
pets, rubber, leather
Wood, paint Sanding of wood or paint in hard-to-reach areas without
sanding paper;
example: Sanding off paint between window shutter slats,
sanding wooden flooring in corners
Fibreglass, mortar, wood Plunge cuts in extremely abrasive materials;
example: Routing of thin mosaic tiles
Expansion joints, window Cutting soft materials;
putty, insulation materials example: Cutting silicone expansion joints or window
(rock wool) putty
Softwood, hardwood, Fast, deep plunge cuts in wood and metal;
veneered boards, plastic- example: Fast cutting of wood containing nails, deep
coated boards, non- plunge cuts in laminated boards and precise shortening of
hardened nails and door frames
screws
Wood, abrasive wood- Fast, deep plunge cuts in wood, abrasive wood-based ma-
based materials, plastics, terials and plastics;
hardened nails and example: Fast cutting of non-ferrous metal pipes and pro-
screws, non-ferrous metal files with small dimensions, easy cutting of non-hardened
pipes nails, screws and steel profiles with small dimensions
Stainless steel, screws Fast, deep plunge cuts in severely abrasive materials or
and nails, epoxy resin, metal;
fibreglass-reinforced example: Fast cutting of kitchen front covers, easy cutting
plastics, fibreglass, plas- through hardened screws, nails and stainless steel.
terboard, porous concrete
Softwood, dowels, pins, Fast, deep separating cuts and plunge cuts;
furniture elements including sawing close to edges in corners and in difficult-
to-reach areas;
example: Deep plunge cut in softwood for installing a vent-
ilation grille
Fitting and Adjusting the Depth Stop
The depth stop (12) can be used when working with seg-
ment saw blades.
Remove the application tool if one has already been fitted.
Slide the depth stop (12) over the tool holder (8) and onto
the collar of the power tool as far as it will go, with the la-
belled side facing upwards.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: Cutting depths 8 mm, 10 mm, 12 mm and
14 mm (information on the depth stop in a larger font size
and without brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: Cutting depths 14 mm, 16 mm, 18 mm and
20 mm (information on the depth stop in a smaller font
size and in brackets).
English | 19
1 609 92A 4K3 | (12.10.2018)